Bryant 4-WAY MULTIPOISE 359AAV страница 3 Скачать руководство пользователя

Страница: 3 / 44

NOTE

: Read the entire instruction manual before starting the

installation.

NOTE

: Please retain these instructions with the furnace after

installation for future reference.

SAFETY CONSIDERATIONS

FURNACE RELIABILITY HAZARD

Failure to follow this warning could result in personal

injury, death or property damage. Improper installation or

misapplication of furnace may require excessive servicing

or cause premature component failure.
Application of this furnace should be indoors with special

attention given to vent sizing and material combustion air

requirements, gas input rate, air temperature rise, unit

leveling, and unit sizing.

CAUTION

FIRE, EXPLOSION, ELECTRICAL SHOCK AND

CARBON MONOXIDE POISONING HAZARD

Failure to follow this warning could result in personal

injury, death, or property damage.
Improper installation, adjustment, alteration, service,

maintenance, or use can cause carbon monoxide poisoning,

explosion, fire, electrical shock, or other conditions which

may cause personal injury or property damage. Consult a

qualified installer, service agency, local gas supplier, or your

distributor or branch for information or assistance. The

qualified

installer

agency

must

use

only

factory--authorized and listed kits or accessories when

modifying this product.

WARNING

Installing and servicing heating equipment can be hazardous due

to gas and electrical components.

Only trained and qualified

personnel should install, repair, or service heating equipment.

Untrained personnel can perform basic maintenance functions

such as cleaning and replacing air filters. All other operations

must be performed by trained service personnel. When working

on heating equipment, observe precautions in literature, on tags,

and on labels attached to or shipped with unit and other safety

precautions that may apply.
These instructions cover the minimum requirements and conform

to existing national standards and safety codes. In some instances,

these instructions exceed certain local codes and ordinances,

especially those that may not have kept up with changing

residential construction practices. We require these instructions as

a minimum for a safe installation.
Wear safety glasses and work gloves. Have a fire extinguisher

available during start--up and adjustment procedures and service

calls.

Recognize safety information. This is the safety--alert symbol

. When you see this symbol on the furnace and in instructions

or manuals, be alert to the potential for personal injury.
Understand the signal words DANGER, WARNING, and

CAUTION. These words are used with the safety--alert symbol.

DANGER identifies the most serious hazards which

will

result in

severe personal injury or death. WARNING signifies a hazard

which

could

result in personal injury or death. CAUTION is used

to identify unsafe practices which

may

result in minor personal

injury or product and property damage. NOTE is used to

highlight suggestions which

will

result in enhanced installation,

reliability, or operation.

CUT HAZARD

Failure to follow this caution may result in personal injury.
Sheet metal parts may have sharp edges or burrs. Use care

and wear appropriate protective clothing and gloves when

handling parts.

CAUTION

TABLE OF CONTENTS

PAGE

IMPORTANT INFORMATION

. . . . . . . . . . . . . . . . . . . . . . . . .

SAFE INSTALLATION REQUIREMENTS

. . . . . . . . . . . . . . .

COMBUSTION & VENTILATION AIR

. . . . . . . . . . . . . . . . . .

CONCENTRIC TERMINATION

. . . . . . . . . . . . . . . . . . . . . . .

GAS SUPPLY & PIPING

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ELECTRICAL WIRING

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

DUCTWORK & FILTER

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CHECKS & ADJUSTMENTS

. . . . . . . . . . . . . . . . . . . . . . . . .

FURNACE MAINTENANCE

. . . . . . . . . . . . . . . . . . . . . . . . .

SEQUENCE OF OPERATION & DIAGNOSTICS

. . . . . . . . .

D E

S I G N

E R

T I F I E

C E RT I F I E D

Always Ask For

Use of the AHRI Certified TM Mark indicates a
manufacturer’s participation in the program. For
verification of certification for individual products,
go to www.ahridirectory.org.

359AA

Содержание 4-WAY MULTIPOISE 359AAV













































Результаты поиска

Содержание 4-WAY MULTIPOISE 359AAV

Отзывы:

Похожие инструкции для 4-WAY MULTIPOISE 359AAV

Бренды по названию

Популярные бренды

Bryant 4-WAY MULTIPOISE 359AAV, Руководство по установке

Результаты поиска

Содержание 4-WAY MULTIPOISE 359AAV

Отзывы:

Похожие инструкции для 4-WAY MULTIPOISE 359AAV

Бренды по названию

Популярные бренды