Bryan Mumford MicroSet Скачать руководство пользователя

Страница: 8 / 32

Page 8

Watch sensors

There are several different sensors you could

use with the MicroSet Watch Timer. The acoustic

sensor that’s included with MicroSet clock timers

will attach to a watch with an alligator clip. This

sensor may work on pocket watches (clip to the

bow), but it’s not the best choice for watches.

It’s not as sensitive as the other watch sensors,

and it might scratch the watch.

The “Simple Watch Sensor” we offer is more

sensitive than the clip-on. It’s a small box with a

brass tube sticking out of the top. Set the watch

on top of this tube. This sensor is able to hear the

component sounds of a tick for the Tick Mode

or Balance Wheel Amplitude measurements.

It’s very modestly priced and is an economical

watch sensor.

The “Clamping Watch

Sensor” is the best watch

sensor we make. Its spring-

loaded arm will hold the

watch in place against the

sensor insuring good contact

for tick transmission. Also, it

has six flat sides so you can

take measurements of the

watch in different positions.

This sensor is the best choice

for serious watchmakers.

The watch sensor made by

Witschi in Switzerland is very

good, and has the advantage

that you can rotate the watch

to various positions without

picking it up. It has the

disadvantage of being very expensive. If you wish to use the Witschi watch holder we

can probably get one for you and provide an interface to adapt it to MicroSet. Contact

Mumford Micro for more information.

You may have a watch sensor from an earlier watch timer, like Vibrograph or Tick-O-

Print. These sensors cannot be used with MicroSet. However, we may be able to update

your old sensor with a new cable and sensing element to be compatible with MicroSet.

Contact Mumford Micro for more information.

Simple Watch Sensor

Clamping Watch Sensor

Содержание MicroSet

































Результаты поиска

Содержание MicroSet

Отзывы:

Похожие инструкции для MicroSet

Бренды по названию

Популярные бренды

Bryan Mumford MicroSet, Быстрый старт

Результаты поиска

Содержание MicroSet

Отзывы:

Похожие инструкции для MicroSet

Бренды по названию

Популярные бренды