background image

4 of 24

REMOTE CONTROL OPERATION

Read and familiarize yourself with the complete

operation of the remote control before attempting

to start the outboard.

IMPORTANT:

The operation of this remote con-

trol may vary from one outboard model to anoth-

er. Refer to outboard’s operator’s guide for

specific instructions related to outboard.

Emergency Stop Feature of Key Switch

Push clip of emergency stop lanyard onto key

switch as shown.

Lanyard 

MUST

 be securely attached to operator.

If operator is thrown from helm, lanyard will pull

clip from key switch to stop outboard.

IMPORTANT:

In an emergency, a passenger

can put control handle in NEUTRAL and restart

outboard without lanyard.

Fast Idle Lever

Use of the fast idle lever is not required on all

models. Refer to operator’s guide for outboard.

The fast idle lever can be used to open throttle

without shifting into gear. With control handle in

NEUTRAL, lift fast idle lever to open throttle for

starting and warm-up. The control is locked in

NEUTRAL when fast idle lever is raised to

prevent shifting into gear at higher than IDLE

RPM. The control handle is unlocked when fast

idle lever is all the way down.

Key Switch

Turn key switch from OFF to ON position. The

warning horn should sound momentarily to

indicate it is working. Turn key to START

position. To use PRIME feature, push and hold

key IN and turn switch to START position.

Release key as soon as motor starts. DO NOT

turn key to START while outboard is running.

Push key IN momentarily (in ON position) for

additional enrichment (PRIME) to keep outboard

running. Not used on all models.

DO NOT run a cold outboard any faster than

necessary to keep it from stalling. DO NOT

exceed 2500 RPM in NEUTRAL. If raised for

starting, push fast idle lever part way down as

soon as outboard starts. For outboards with

Quikstart™, 

wait until engine slows to IDLE RPM

before shifting into gear. Refer to operator’s guide

for specific instructions related to outboard.

1. Emergency stop clip

004848

1. Key switch
2. Lanyard

004850

WARNING

Lanyard MUST be securely attached to
operator, and clip MUST be installed on
key switch. DO NOT operate outboard with
clip removed from switch, except in an
emergency. 

1

2

1

1. Fast idle lever

004851

004852

1

Содержание 5006180

























Отзывы: