Brother P-TOUCH PT-H110, Руководство пользователя

Страница: 14 / 17

HELPFUL HINTS
X
Error message
X
What to do when...
Troubleshooting
6
Message Cause/Remedy
Battery Low! The batteries are weak.
If using AAA alkaline batteries: Replace them
with six new AAA alkaline batteries. Do not use
old and new batteries together or mix alkaline
batteries with other battery types.
If using Ni-MH batteries: Charge them fully.
Battery Empty! The installed batteries are running low and
need to be changed for continued operation.
Invalid! • There is no text above the cursor when you
selected [Numbering].
• You selected an invalid character for
[Numbering].
• You selected an invalid number for [Label Length].
• You entered an invalid value as the label
length while using templates.
No Text! • You tried to print a text file when there is no
data stored in the memory.
• You pressed when no text is entered.
• You pressed when no text is entered.
• You pressed or when no text was
entered while using templates.
2 Line Limit!/
1 Line Limit!
• You tried to enter a 3rd line by pressing .
• You tried to print or preview two lines of text
while 0.13" (3.5mm) or 0.23" (6 mm) tape is
installed. Install larger tape size.
No Cassette! You tried to print, feed or preview a label when
there is no cassette installed.
Cutter Pressed You pressed the tape cutter lever in the middle
of printing process.
Text Full! You have already entered the maximum
number of characters allowed (80 characters
for text, 50 characters for templates. If your
message contains symbols, the maximum
number of characters could be reduced.).
Text Limit!
Change Length Since the number of entered characters
exceeds the label length, reduce the text, or
select [Auto] as the label length.
No Frame OK? • Printing on 0.13" (3.5mm) tape with invalid
Frame setting ON.
(Select to print with no Frame,
to cancel.)
Feed OK? • Feeding tape after printing when [Chain Print]
is selected. See “Setting Margin”.
Insert 0.47" • Only 0.47"(12mm) tape cassette is available
for templates.
Wrong Tape!
Use TZe tape
• Use a tape cassette with the mark.
Problem Solution
The display
stays blank
after you have
turned on the
label maker. • Check that you installed the batteries
correctly with the positive and negative ends
in the correct position.
• If the batteries are weak, replace them with six
new AAA alkaline batteries. Do not use old
and new batteries together or mix alkaline
batteries with other battery types.
• Check that you connected the AD-24ESA
adapter correctly.
When the label
is printed out,
there is too
much margin
(space) on both
sides of the text.
• See “Setting Margin” in this users guide and
select [Half] or [Narrow] to have smaller
margins for your label.
The label maker
does not print, or
the printed
characters are not
formed correctly. • Check that you have inserted the tape
cassette correctly.
• If the tape cassette is empty, replace it.
• Check that you closed the cassette cover
correctly.
The label
maker's
settings have
cleared on its
own. • The batteries may be weak. Replace them
with six new AAA alkaline batteries. Do not
use old and new batteries together or mix
alkaline batteries with other battery types.
• When power is disconnected for more than
three minutes, all text and formats in the display
are lost.
A blank horizontal
line appears
through the
printed label. • There may be some dust on the print head.
Remove the tape cassette and use a dry
cotton swab to gently wipe the print head with
an up-and-down motion.
The label maker
has “locked up”
(that is, nothing
happens when a
key is pressed,
even though the
label maker is on.)
• See “Resetting the label maker”.
The power
turns off when
you try to print. • The batteries may be weak. Replace them
with six new AAA alkaline batteries. Do not
use old and new batteries together or mix
alkaline batteries with other battery types.
• Check that you inserted the batteries correctly.
• A wrong adapter is used; the recommended
adapter is the AD-24ESA.
The tape does
not feed
correctly or the
tape gets stuck
inside the label
maker.
• Check that the end of the tape feeds under
the tape guides.
• The cutter lever is pressed while printing. Do
not touch the cutter lever during printing.
To change
language setting.
• See "Initial Settings".