Brother HL-6050DN Скачать руководство пользователя

Страница: 130 / 181

ROUTINE MAINTENANCE 5 - 15

Cleaning the inside of the printer

Clean the inside of the printer as follows:

Turn off the printer power switch, and then unplug the printer power cord.

Press the cover release button and then open the front cover of the printer.

Figure 5-24

Take out the drum unit assembly (drum unit with the toner cartridge).

Figure 5-25

When you clean the inside of the printer, pay attention to the following:

■

If your clothes are smeared with toner, wipe off the toner with a dry cloth and immediately wash
the clothes in cold water to avoid stains.

■

Be careful not to inhale the toner.

■

After you have just used the printer, some parts inside the printer are extremely hot. When you
open the front cover of the printer, never touch the fuser and fixing roller.

Figure 5-23

Содержание HL-6050DN






















































































































































































Результаты поиска

Содержание HL-6050DN

Отзывы:

Похожие инструкции для HL-6050DN

Бренды по названию

Популярные бренды

Brother HL-6050DN, Руководство пользователя

Результаты поиска

Содержание HL-6050DN

Отзывы:

Похожие инструкции для HL-6050DN

Бренды по названию

Популярные бренды