manualshive.com logo in svg

Brother DCP-J925DW, Руководство по обслуживанию

Поделиться
Скачать
Brother DCP-J925DW Скачать руководство пользователя страница 275

4-22

Confidential

2.2

Customize the EEPROM on the main PCB (Function code 74)

Refer to 

Chapter 5, Section 1.4.26

.

Note:

 Once this procedure is carried out, it is necessary to write the corresponding language

data, so be sure to write local programs, referring to 

Section 2.4

 below.

2.3

Initialize the EEPROM on the main PCB (Function code 01)

Refer to 

Chapter 5, Section 1.4.1

.

2.4

Load local programs

Note: 

This procedure is not required when no EEPROM customizing has been performed with

Function code 74 in 

Section 2.2

 in this chapter.

Reload local program, referring to 

Section 2.1.2 "If the main PCB loaded with programs is used

(Updating existing programs)

."

2.5

Restore machine information (Function code 46)

Restore the machine information and user setting information that have been backed up in an
external memory, referring to 

Chapter 5, Section 1.4.12

.

If the machine information is successfully restored, it is not necessary to perform operations given in

Sections 

2.9

 

to

 

2.13

 and 

2.17

.

If the machine has failed to back up the machine information into an external memory at the
start of repair, replace the ink absorber box and flushing box, and then reset each of the purge
and flushing counts with the following procedure.

(1) Switch the machine to the maintenance mode. (Refer to 

Chapter 5

.)

(2) Press the 

8

 and 

0

 keys in this order.

(3) Press the 

Black

 

Start

 (

Mono Start

) key several times until the purge (or flushing) count

appears on the LCD.

(4) Press the 

2

, 

7

, 

8

 and 

3

 keys in this order to reset the purge (or flushing) count.

(5) Press the 

Stop/Exit

 key to return to the initial stage of the maintenance mode.

2.6

Restore head calibration data (Function code 68)

Restore head calibration data that has been backed up, referring to 

Chapter 5, Section 1.4.23

.

If restoring head calibration data ends successfully, it is not necessary to perform operations
given in 

Section 2.14

.

2.7

Check the sensor operation (Function code 32)

Refer to 

Chapter 5, Section 1.4.11

.

2.8

Specify the CIS type (Function code 59)

Refer to 

Chapter 5, Section 1.4.18

.

Содержание DCP-J925DW



























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды