Brother DCP-J925DW Скачать руководство пользователя страница 273 | Manualshive

Страница: 273 / 378

Brother DCP-J925DW Скачать руководство пользователя страница 273

4-20

Confidential

2.1.2 If the main PCB loaded with programs is used (Updating existing programs)

A main PCB used for any other machine has been loaded with programs. If the current main
PCB is replaced with such a used PCB, update existing programs using the procedure given
below.

Load firmware using an external memory

Load firmware in the maintenance mode (Function code 28), referring to

Chapter 5, Section

Loading firmware with this procedure inherits fax data stored in the main PCB.

Load firmware using a PC

[ A ] .pjl firmware file

Loading firmware with this procedure inherits fax data stored in the main PCB.

(1) Turn the machine on and switch it to the maintenance mode (refer to

(2) On the PC, run "filedg32.exe."

The Filedrgs window appears.

(3) Drag and drop the target firmware (e.g., lz00001_a.pjl) onto the Brother Maintenance USB

Printer driver icon in the Filedrgs window.

Note:

To use a firmware file, extract it beforehand by double-clicking. It is a self-extracting

file having the extension .exe.

After approx. 2 to 3 minutes, the loading operation is complete and the machine
automatically reboots and returns to standby.

(4) On the machine, display the version of the installed firmware on the LCD by pressing the

*

and

#

keys simultaneously (for models with numerical keypad) or by pressing the

and

Stop/Exit

keys simultaneously (for models without numerical keypad).

Sample version number shown on the LCD: 0A810060953:4B69
(The top line shows the version number.)

P0601242005:4123
B0601242005:1C8D

If the displayed version number is identical with the firmware version you installed, the
loading operation has been successfully finished.

Note:

If loading operation ends abnormally, turn the machine off and on. Wait for the machine

to emit a long beep and automatically enter the firmware loading mode, and then perform the
loading procedure above again.

[ B ] .pmu firmware file

Loading firmware with the following procedure deletes fax data stored in the main PCB.

Unplug the power cord of the machine from the electrical outlet and make sure that the machine
is connected to your PC with a USB cable.

(1)

Models with numerical keypad

While holding down the

5

key, plug the power cord into

an electrical outlet.

Models without numerical keypad

While holding down the

and

Stop/Exit

keys

simultaneously, plug the power cord into an electrical outlet.

When the black and white pattern shown above is displayed, the machine is ready to
receive programs or data for firmware installation from the connected PC.

«
...
271
272
273
274
275
...
»

Содержание DCP-J925DW



























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды