Brother DCP-J925DW Скачать руководство пользователя страница 285 | Manualshive

Страница: 285 / 378

background image

5-1

Confidential

CHAPTER 5 SERVICE FUNCTIONS

This chapter describes the maintenance mode and other service functions, which are exclusively
designed for the purpose of checks, settings and adjustments of the machine and can be triggered by the
keys on the control panel*.

* For key operations, refer to

in this chapter.

1

MAINTENANCE MODE

In the maintenance mode, you can update memory (EEPROM: electrically erasable programmable
read-only memory) contents for optimizing the drive conditions of the head/carriage unit and paper
feed roller/paper ejection roller in the engine unit, if those units have been replaced, or for setting the
CIS scanner area, for example. You can also customize the EEPROM according to the shipment
destination of the machine concerned. In addition, you can perform operational checks of the LCD,
panel PCB or sensors, perform a print test, display the log information or error codes, and configure
firmware switches (WSW).

1.1

Entry to the Maintenance Mode

1.1.1 How to Enter the End User-accessible Maintenance Mode

Basically, the maintenance-mode functions listed in

in this chapter should be

accessed by service personnel only. However, you can allow end users to access some of these
under the guidance of service personnel (e.g., by telephone).

The user-accessible functions are

shaded

in the table given in

. Function code 10

accesses the firmware switches, each of which has eight selectors. You should not allow end
users to access all of those selectors, but you can allow them to access user-accessible selectors
which are

shaded

in the firmware switch tables in the "Firmware Switches (WSW)" document

separately issued.

The service personnel should instruct end users to follow the procedure given below.

(1)

Models with

key

Press the

and

Black Start

(

Mono Start

) keys simultaneously. Then press the

Black

Start

(

Mono Start

) and

keys in this order.

Models without

key

Press the

Menu

,

Black Start

(

Mono Start

) and

Menu

keys in this order.

Tip:

Either of the following operations also makes the machine enter the maintenance

mode.
- Press the

Menu

,

Black Start

(

Mono Start

), and

0

keys in this order, in the same way as

conventional models.

- While holding down the

Color Start

key, plug the power cord into an electrical outlet.

(2) Wait for the machine to display "

" on the LCD, indicating that the

machine is ready to accept entry from the keys. Enter the desired function code.

(3) To quit the maintenance mode operation in midway and switch to standby, press the

Stop/

Exit

key. When each of the user-accessible functions is completed, the machine

automatically returns to standby.

Note:

The operating procedure of the user-accessible maintenance mode may differ slightly

depending upon machine models.

«
...
283
284
285
286
287
...
»

Содержание DCP-J925DW



























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DCP-J925DW

Бренд: MAKERGEAR Страницы: 8

Бренд: Oki Страницы: 2

Figure 4 Standalone

Бренд: 3D Systems Страницы: 2

Бренд: Z Corporation Страницы: 99

Бренд: Printek Страницы: 34

Бренд: Magicard Страницы: 108

Бренд: Olivetti Страницы: 204

Бренд: SPRT Страницы: 18

WORKCENTRE 7428

Бренд: Xerox Страницы: 208

Бренд: Ricoh Страницы: 4

Бренд: MostFun Страницы: 25

Бренд: NEC Страницы: 90

Бренд: Epson Страницы: 4

Бренд: Epson Страницы: 36

Бренд: Epson Страницы: 4

Бренд: Epson Страницы: 115

Бренд: Epson Страницы: 248

Бренд: Epson Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды