Brother DCP 7065DN Скачать руководство пользователя страница 90

Страница: 90 / 337

2-53

Confidential

Error code 97

Error, which cannot be specified, occurs.

Error code 98

Error, which cannot be specified, occurs.

Error code 99

Error, which cannot be specified, occurs.

■

Error code 9A

The paper cannot detected when the paper is fed from the manual feed slot.

Size mismatch
Reload correct paper, then press Start.

Size mismatch DX
Press Job Cancel. Specify the correct paper and load the same size

paper as the Printer driver setting.

<User Check>

• Turn OFF the power switch, and turn it ON again after a while.

Step

Cause

Remedy

Main PCB failure

Replace the main PCB ASSY.

Manual Feed
Load Paper.

<User Check>

• Load the paper into the manual feed slot.

Step

Cause

Remedy

Harness connection failure of

registration front/rear sensor PCB

ASSY.

Check the harness connection of the

registration front/rear sensor PCB ASSY

and reconnect it.

High voltage power supply PCB

failure

Replace the high voltage power supply

PCB ASSY.

Main PCB failure

Replace the main PCB ASSY.

Registration front sensor failure

Check the registration front sensor

performance following the procedure

described in

"Function code 32"

. If any

problem occurs, replace the regist frame

ASSY.

Содержание DCP 7065DN


















































































































































































































































































































































Результаты поиска

Содержание DCP 7065DN

Отзывы:

Бренды по названию

Популярные бренды

Brother DCP 7065DN, Руководство по обслуживанию

Результаты поиска

Содержание DCP 7065DN

Отзывы:

Бренды по названию

Популярные бренды