Brother DCP 7065DN Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 337

Brother DCP 7065DN Скачать руководство пользователя страница 48

2-11

Confidential

2.6

Life of Toner Cartridge and Drum Unit

<Life of Toner Cartridge>

This product detects the remaining toner only by the dot count and the number of rotations of
the develop roller. The function to detect by the light sensor is not installed. As this machine
is not equipped with a toner sensor as conventional models are, it manages the level of
remaining toner by dot count during printing and the number of rotations of the develop roller.
Therefore printing may stop with the error message “Replace Toner” even though some toner
remains. Even if “Replace Toner” is displayed on the machine, printing can be continued if
the user chooses to change the mode to Continue Mode. In Continue Mode, however, the
printing result when the toner runs out is not assured, meaning that the user shall be
responsible for it. In addition to this, even when the mode is set to Continue Mode, printing
stops when the number of rotations of the develop roller reaches the upper limit, and remains
stopped until the toner cartridge is replaced to prevent any problems, such as toner leakage.

The life of the toner cartridge varies according to the average number of print pages per job.
(See the table below.) The number of printable pages is larger when making continuous
prints in one job because deterioration of the develop roller is low.

Relationship between average print page per 1 job and life of toner cartridges

26/27ppm model

24ppm model

20/21ppm model

The develop roller also rotates for the warm-up operation when the power is turned ON and
when the cover is opened or closed. Therefore, when these operations are frequently
performed, the life of toner cartridges is shortened. (The table below shows the worst case in
which the warm-up operation is performed when the power is turned ON.)

Average print page (page/job)

1

2

3

· · ·

Continuance

Cartridge life (Starter)

630

950

1200

2100

Cartridge life (Standard)

1080

1600

2000

3600

Cartridge life (High-capacity)

2340

3500

4300

7800

Page

Average print page (page/job)

1

2

3

· · ·

Continuance

Cartridge life (Starter)

630

930

1100

2000

Cartridge life (Standard)

1080

1600

2000

3400

Cartridge life (High-capacity)

2340

3500

4200

7400

Page

Average print page (page/job)

1

2

3

· · ·

Continuance

Cartridge life (Starter)

630

930

1100

2000

Cartridge life (Standard)

900

1300

1600

2900

Cartridge life (Standard) (HL-2220)

1080

1600

2000

3500

Cartridge life (High-capacity) (HL-2220)

2340

3500

4200

7600

Page

«
...
46
47
48
49
50
...
»

Содержание DCP 7065DN


















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды