
Chapter 9 Error code list
BES-116AC
136
Errors E-1C and E-1D are not displayed due to mechanical problems.
E-00
E-01
E-02
E-03
E-04
E-05
E-09
E-0A
E-0B
E-0C
E-0D
E-0F
E-14
E-15
E-16
E-17
E-1A
E-1C
E-1D
E-21
E-22
E-23
E-24
E-25
E-26
E-27
E-28
E-29
E-2A
E-2B
ERROR 00
ERROR 01
Overtravel
Stop SW was pressed during
home positioning
Zero positioning is out of range
Needle stop position error
X-axis home position error
Thread breakage error
ERROR 0B
ERROR 0C
ERROR 0D
ERROR 0F
Y-axis home position error
Press
for reatart.
ERROR 16
ERROR 17
ERROR 1A
Restart perimeter
Stop while transferring to next
repeat pattern
Area over
Area over
Area over
Area over
Area over
Area over
Area over
Area over
Area over
Area over
Area over
No error occurs.
Either motor of main shaft, X- or Y-axis has
locked.
Overtravel occurs during home position detect-
ing movement.
The stop switch is pressed during home position
detecting movement.
Zero detecting movement out of range
Needle stop position error
X-axis home position detection error
Thread breaking error
Stop or emergency stop during sewing
Insufficient bobbin thread
The machine does not return to the home position.
Undefined error
Y-axis home position error
Stop error during SSP processing (when press-
ing the stop key while the hoop is moving)
Needle with specified number is out of movable
area.
Speed Vol. No. is out of range.
Destination coordinates error
The machine stops during mask tracing.
The machine stops while the needle is moving
between patterns during repeat sewing.
Hoop ovX)
Hoop ovY)
Hoop ovX, +Y)
Hoop overhang(-X)
Hoop ovX, -X)
Hoop overhang(-X, +Y)
Hoop ovX, -X, +Y)
Hoop overhang(-Y)
Hoop ovX, -Y)
Hoop ovY, -Y)
Hoop ovX, +Y, -Y)
This is not usually displayed.
Turn the power off and on once. If the same error occurs
again, the area sensor is faulty.
Press the
STOP
to restart the home position detecting movement
again.
Turn the power off and on once. If the same error occurs
again, the home position sensor is faulty.
Adjust the pulley stop position (100 degrees) above the
needle and press the
STOP
.
Turn the power off and on once. If the same error occurs
again, the X-axis mechanism is faulty.
After passing through the thread, press the
STOP
.
This is not usually displayed.
Turn the power off and on once. If the same error occurs
again, the Y-axis mechanism is faulty.
Hoop movement restarts if you press
.
This is not usually displayed.
Tracing is cancelled if the
STOP
key is pressed when the ma-
chine is stopped during mask tracing. Press the
key to
continue tracing.
This is displayed when the stop switch is pressed while the
hoop is moving. Press the
to move the hoop again. (It is
necessary to press the
again to start sewing.)
Pattern or the needle position is out of the embroidering area.
Reset the embroidering area on the panel or move the hoop to
the sewable position.
Code
Error Messages
Error
Measures
Содержание BES-116
