Brother 9500 - HL 1660EN B/W Laser Printer Скачать руководство пользователя | Manualshive

Страница: 152 / 258

background image

CHAPTER 4 CONTROL PANEL

4–85

TEST Switch

You can test the printer or print out the list of fonts with the TEST switch.
To do so, hold down the SHIFT switch and press the TEST switch. You
will then enter the test mode where you may test the printer or print out
the list of fonts.

To test the printer, follow these steps:

1. Press the SEL switch to set the printer off-line.

2. Hold down the SHIFT switch and press the TEST switch.

When you enter the test mode, the display shows the first test mode
item.

DEMO PAGE

3. Press the

▲

or

▼

switch until the desired test mode appears on the

display.

Display Message Test Mode

DEMO PAGE

Prints out the demonstration.

TEST PRINT

Performs the printer test and prints
out the test pattern.

PRINT CONFIG

Prints out the list of panel switch
settings you have configured for
the printer as user settings.

PRINT FONTS I

Prints out the list of internal or
resident fonts.

PRINT FONTS C

Prints out the list of optional fonts
stored in the font cartridge/card.

PRINT FONTS P

Prints out the list of permanent
download fonts.

exit

Exits from the test mode. The
printer does not perform the test.

«
...
150
151
152
153
154
...
»

Содержание 9500 - HL 1660EN B/W Laser Printer



































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 9500 - HL 1660EN B/W Laser Printer

Бренд: MAKERGEAR Страницы: 8

Бренд: BIXOLON Страницы: 59

Бренд: GCC Technologies Страницы: 2

Бренд: Radio Shack Страницы: 42

Бренд: Oki Страницы: 157

Бренд: X-media Страницы: 10

Бренд: Noztek Страницы: 8

Бренд: Xerox Страницы: 85

Бренд: HCC Technology Страницы: 71

Бренд: Panduit Страницы: 39

Бренд: Ricoh Страницы: 68

Phaser 6128 MFP

Бренд: Xerox Страницы: 4

Бренд: Oki Страницы: 56

Бренд: DigiPos Страницы: 14

pixma ip7250 series

Бренд: Canon Страницы: 4

Бренд: Canon Страницы: 4

Бренд: Canon Страницы: 10

Бренд: Canon Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды