Bromic Heating Tungsten 2000W, Инструкция по установке, эксплуатации и обслуживанию

Страница: 7 / 7

12 13
www.bromicheating.com www.bromicheating.com
For longest product life & to maintain product appearance
mount heater under cover & protect from rain & weather
whenever possible.
The exterior housing of the heater should be cleaned
regularly with a soft damp cloth. For locations near the
coast, salt in the air can cause rusting of metal. Additional
cleaning of the heater with a soft damp cloth fortnightly will
increase the life of the products appearance.
Ensure that there is no excessive build-up of dirt/dust on
the reflectors or elements as this can cause overheating
and premature element failure. To clean the reflectors and
elements, ensure heater is off and has been off for at least 2
hours after operation, and wipe off any dirt/dust with a soft
& dry cloth.
MAINTENANCE
SERVICING
TUBE ELEMENT REPLACEMENT
WARNING
ELECTRICAL SHOCK HAZARD!
Serious injury or death may occur.
Disconnect from electrical supply before servicing this
heater.
!
!
WARNING
Servicing and maintenance MUST be carried out by an
authorised and licensed person only
1. Remove Front Cover of the heater by unscrewing the 3
screws holding it in place.
2. Remove first Element End Cover by unscrewing the 2
screws holding it in place.
3. Open first Element Lock Bracket by removing screw.
4. Remove outer Hex Nut, Spring Washer and Lead Wire
Ring Terminal from the threaded stud.
5. Repeat steps 2-4 to release second end of element.
6. Remove old Tube Element.
7. Assemble new Tube Element.
Hex Nut, Spring Washer and Ring Terminal must be
assembled tightly at both ends of element.
8. Element Lock Brackets and Element End Covers must
be replaced at both ends of the heater. Assemble front
cover and secure with 3 screws.
REPLACEMENT PART LIST
No. Description BH0420006
(2000W)
BH0420007
(3000W)
BH0420008
(4000W)
BH0420009
(6000W)
1 Tube Element BH8180001 BH8180002 BH8180001 BH8180002
2 Front Cover BH8180003 BH8180004 BH8180003 BH8180004
3 Element End Cover Set BH8180005 BH8180006 BH8180005 BH8180006
4 Junction Box Cover & Seal Set BH8180007 BH8180007 BH8180007 BH8180007
5 Mounting Bracket Set (Short) BH8180008 BH8180008 BH8180008 BH8180008
6 Mounting Bracket Set (Long) BH8180009 BH8180009 BH8180009 BH8180009
7 Tube Suspension Kit BH8180012 BH8180012 BH8180012 BH8180012
8 Chain Suspension Kit BH8180013 BH8180013 BH8180013 BH8180013
SYMPTOM POSSIBLE CAUSE (S) CORRECTIVE ACTION
Element does not energize 1. Defective element
2. Improper connection 1. Replace element
2. Check connection to power
outlet
Not enough heat 1. Heater too small for application
2. Heater mounted too high or too
far 1. Add additional heater(s)
2. Decrease mounting height or
distance
Too much heat 1. Heater too large for application
2. Heater mount too low or too close 1. Replace with smaller heater
2. Increase mounting height or
distance
Hot spot in Tube 1. Heater is not level
2. Grease or moisture on tube 1. Adjust to level mount
2. Clear tube-replace if problem
persists
TROUBLESHOOTING
4000W & 6000W Models 2000W & 3000W Models
4000W & 6000W Models 2000W & 3000W Models
1.
2.
3.
4.
Version 1.0ES Revised: 04/09/2013