Brocade Communications Systems Converged Enhanced Ethernet 8000 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 168

background image

38

Converged Enhanced Ethernet Administrator’s Guide

53-1002163-02

Configuring Spanning Tree Protocol

5

DRAFT: BROCADE CONFIDENTIAL

Configuring Spanning Tree Protocol

Spanning Tree Protocol (STP) is a mechanism to detect and avoid loops in Ethernet networks by
establishing a fixed path between all the switches in a LAN. The Brocade FCoE hardware supports
three spanning tree variations: standard Spanning Tree Protocol (STP), Rapid Spanning Tree
Protocol (RSTP), and Multiple Spanning Tree Protocol (MSTP).

NOTE

Configuring Spanning Tree on a port enabled for FCoE is not recommended, as it can cause login
issues while the port transitions from the blocked state to the forwarding state. Either STP should
be disabled, or configured in edge mode. However, Brocade strongly recommends that STP be
disabled.

It is a best practice that an access layer switch does not become the root switch. Changing the
bridge or STP priority helps to ensure that this does not occur. The following example performed
from the CEE CLI configures the switch for RSTP and sets the bridge priority to the highest value,
ensuring it will not become the root switch in an existing LAN.

To configure RSTP, perform the following steps in global configuration mode.

1. Configure the switch for RSTP.

switch(config)#

protocol spanning-tree rstp

2. Set the bridge priority to the highest value so it does not become the root switch in an existing

LAN.

switch(conf-rstp)#

bridge-priority 61440

3. Enter the copy command to save the running-config file to the startup-config file.

switch(conf-rstp)#

do copy running-config startup-config

Configuring VLAN membership

IEEE 802.1q Virtual LANs (VLANs) provide the capability to overlay the physical network with
multiple virtual networks. VLANs allow network traffic isolation into separate virtual networks,
reducing the size of administrative and broadcast domains.

A VLAN contains end stations that have a common set of requirements which can be in
independent physical locations. You can group end stations in a VLAN even if they are not
physically located in the same LAN segment. VLANs are typically associated with IP subnets and all
the end stations in a particular IP subnet belong to the same VLAN.

In addition to creating a special VLAN for FCoE traffic, VLAN classifiers are applied to incoming
EtherTypes for FCoE Initialization Protocol (FIP) and FCoE. VLAN classifiers are rules used to
dynamically classify Ethernet frames on an untagged interface to VLANs.

NOTE

FIP and FCoE cannot be manually configured in VLAN classifier rules. They are part of the fcoeport
interface configuration and are applied automatically when an interface is configured as an
fcoeport.

«
...
58
59
60
61
62
...
»

Содержание Converged Enhanced Ethernet 8000









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Converged Enhanced Ethernet 8000

Бренд: Makita Страницы: 2

BiPAC 4500NZ(L)

Бренд: Billion Страницы: 146

Netlink FRX8000

Бренд: Cabletron Systems Страницы: 94

MMAC-Plus 9E423-24

Бренд: Cabletron Systems Страницы: 10

MMAC-Plus 9A128-01

Бренд: Cabletron Systems Страницы: 22

Spectrum EMM-E6

Бренд: Cabletron Systems Страницы: 2

SmartSTACK ELS100-24TXG

Бренд: Cabletron Systems Страницы: 112

Бренд: Cabletron Systems Страницы: 86

Бренд: Cabletron Systems Страницы: 54

Cabletron BRIM-F6

Бренд: Cabletron Systems Страницы: 43

Netlink FRX4000

Бренд: Cabletron Systems Страницы: 60

CSX200 CyberSWITCH

Бренд: Cabletron Systems Страницы: 2

Бренд: Cabletron Systems Страницы: 8

Бренд: Cabletron Systems Страницы: 4

Бренд: Amperes Страницы: 8

Бренд: Winext Страницы: 37

XM24 Expansion Module

Бренд: Avaya Страницы: 5

Бренд: SIIG Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды