Brocade Communications Systems Converged Enhanced Ethernet 8000 Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 168

background image

36

Converged Enhanced Ethernet Administrator’s Guide

53-1002163-02

Configuring the FCoE VLAN

5

DRAFT: BROCADE CONFIDENTIAL

VLAN 1002 is reserved for FCoE VLAN. If VLAN 1002 is already assigned as a LAN VLAN, it is
automatically recreated as the FCoE VLAN while creating the default fcoe-map.

The FCoE VLAN can be created in the FCoE map configuration mode as well. The fcoe-vlan
command creates the FCoE VLAN if the corresponding VLAN does not exist in the system. If a VLAN
already exists with the same VLAN ID, then the command fails.

The FCoE VLANs can be seen using the show vlan fcoe command. Alternatively, the show vlan brief
command can be used, in which FCoE VLANs are marked with an “(F)”.

No VLAN classifiers (including FIP and FCoE classifiers) are allowed to be configured for the FCoE
VLAN.

To configure the FCoE VLAN, perform the following steps in global configuration mode.

1. Activate the FCoE map configuration mode.

switch(config)#

fcoe-map default

switch(conf-fcoe-map)#

2. Use the fcoe-vlan command to specify a new VLAN ID.

Only one FCoE VLAN can be active at a time, and this command will be successful only if the
new VLAN ID can be created and the old VLAN ID can be deleted. The FCoE VLAN cannot be
changed if the fcoeport profile is already applied to an interface.

switch(conf-fcoe-map)#

fcoe-vlan 5

3. Use the do show vlan fcoe command to confirm the VLAN ID change.

switch(conf-fcoe-map)#

do show vlan fcoe

VLAN Name State Ports
(F)-FCoE (u)-Untagged, (t)-Tagged
======= ================ ======= ===============================
5(F) VLAN0005 ACTIVE

4. Use the do show fcoe-map command to confirm the current status of the FCoE map.

The following example shows that the FCoE VLAN has been assigned the ID of 5, but the map
has not been assigned to any interfaces.

switch(conf-fcoe-map)#

do show fcoe-map

fcoe-map default
cee-map : default
fcoe-vlan : 5
interface(s) :

Assigning an FCoE map onto an interface

The FCoE map cannot be edited if it is associated with any interfaces.

The FCoE map can be applied, irrespective of whether or not the interface is in ‘switchport’ mode.
But the FCoE map cannot be applied on an interface if the same interface already has a CEE map
assigned to it.

To assign the FCoE map onto an interface, perform the following steps in global configuration
mode.

1. Activate the interface configuration mode for the interface you wish to modify.

The following example activates the mode for the 10 Gigabit Ethernet interface in slot 0/port 0.

switch(config)#

interface tengigabitethernet 0/0

«
...
56
57
58
59
60
...
»

Содержание Converged Enhanced Ethernet 8000









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Converged Enhanced Ethernet 8000

Ray 3 Plus Client

Бренд: Sun Microsystems Страницы: 6

Бренд: Omnia Страницы: 6

Pixie-4 Express

Бренд: XIA Страницы: 17

Бренд: Paradyne Страницы: 45

Бренд: AMD Страницы: 20

Бренд: Aztech Страницы: 2

Бренд: IBA Страницы: 33

Бренд: EVS Страницы: 30

Бренд: SIIG Страницы: 6

IBOX-BAC Series

Бренд: IntesisBox Страницы: 2

WRT54GR - Wireless-G Broadband Router

Бренд: Linksys Страницы: 81

Бренд: Juniper Страницы: 825

Бренд: OpenVox Страницы: 13

Бренд: QuickLink Страницы: 8

UniFi Cloud Key

Бренд: Ubiquiti Страницы: 13

Бренд: Lutron Electronics Страницы: 4

Бренд: Advantech Страницы: 68

UniFi WiFi BaseStation XG

Бренд: Ubiquiti Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды