Brobo OHS Series Скачать руководство пользователя страница 8

Страница: 8 / 58

Fowler

Road

Dandenong

South

Vic

3175

brobo.com.au

+61

9794

8751

[email protected]

PART 2 CONNECT TO POWER SOURCE

POWER SUPPLY

The 415/240V power supply requirements for this machine are of a high level & unautho-

rized interference and/or inadequate maintenance could result in a situation that could put

the operator at risk. A qualified electrical engineer should always be assigned to maintain &

repair the system.

International Protection Rating code (Ingress Protection): IP54

First Digit: Solid - Level 5: Protected from limited dust ingress.

Second Digit: Liquid – Level 4: Protected from water spray from any direction.

SINGLE & THREE PHASE

Single phase

machines are provided with

three pins

, 15 amps rated plugs & leads for con-

nection to 240V, 50Hz power supply in Australia.

Active = Brown

Brown

VOLTAGE

MAIN

VOLTAGE

Neutral = Light Blue

Light Blue

240V/1

240V

Earth = Green

Green

/Yellow

Yellow

Three phase

machines should be fitted with a suitable, approved

four pin plugs

Active = Brown

Brown

, White. Dark Blue

VOLTAGE

MAIN

VOLTAGE

Earth = Green

Green

/Yellow

Yellow

415V/3PH

WARNING

Before connecting the machine to the power supply, check that the socket is not

connected in series with other machines. This condition is critical for the ideal op-

eration of the saw unit.

Содержание OHS Series



























































Результаты поиска

Содержание OHS Series

Отзывы:

Бренды по названию

Популярные бренды

Brobo OHS Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание OHS Series

Отзывы:

Бренды по названию

Популярные бренды