Brobo OHS Series Скачать руководство пользователя страница 10

Страница: 10 / 58

Fowler

Road

Dandenong

South

Vic

3175

brobo.com.au

+61

9794

8751

[email protected]

PART 3 SAFETY & ACCIDENT PREVENTION

The

Brobo Group S315/S350/S400

Series Metal Cutting Saw has been designed & man-

ufactured in accordance with

Australian Standards.

It is

HIGHLY RECOMMENDED

that the

instructions & warnings contained in this chapter be carefully followed for correct usage of

the machine.

OPERATION OF THE MACHINE

The

Brobo Group S315/S350/S400

Series Metal Cutting Saw is specifically designed to

cut ferrous & non-ferrous metal cross sections with solid or thin-walled profiles. Other types

of material & machining are not compatible for use with the specifications of the saw. This

machine involves a

high-speed blade rotation

; therefore

extreme caution is required

when

operating the device.

The employer is responsible for instructing the personnel who, in turn, are obliged to inform

the operator of any accident risks, safety devices, noise emission & accident prevention reg-

ulations provided for by national & international laws governing the use of the machine.

The

operator must be fully aware of the position & functions of all the machine’s controls.

All those concerned must strictly adhere to ALL instructions, warnings, & accident prevention

standards in this manual.

The following definitions are those provided for by the

EEC DIRECTIVE ON MACHINERY No.

98/37/CE:

Danger Zone

- any zone in and/or around a machine in which the presence of a person con-

stitutes a risk for the safety & health of that person.

Person Exposed

- any person finding him or herself, either completely or partly in a danger

zone.

Operator

- the person or persons are given the responsibility of installing, operating, adjust-

ing, maintaining, cleaning, repairing, & transporting the machine.

NOISE LEVEL

The noise level of an idling metal saw, fitted with a 180-tooth blade (supplied as standard

by Brobo Group) has been measured to be

below 85 dBA

. This complies with the

Australian

Occupational Health & Safety (Noise) Regulations 1992.

Please note that peak impulse noise levels will be experienced due to variables including blade

characteristics, type, & condition. This will also vary accordingly depending on the size &

type of sample being cut. Under these circumstances, management should make available

to the operator(s) the

appropriate hearing protection equipment

as prescribed under the

above-stated act.

WARNING – UNAUTHORISED MODIFICATIONS/REPLACEMENTS/USE

The manufacturer declines any responsibility whatsoever, either civil of criminal,

in the case of unauthorised interference or replacement of one or more parts or

assemblies on the machine, or if accessories, tools & consumable materials used

are different from those recommended by the manufacturer, or if the machine is

inserted in a plant system & its proper function is altered.

Содержание OHS Series



























































Результаты поиска

Содержание OHS Series

Отзывы:

Бренды по названию

Популярные бренды

Brobo OHS Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание OHS Series

Отзывы:

Бренды по названию

Популярные бренды