READ AND SAVE THESE INSTRUCTIONS
PRODUCT STRUCTURE AND DIMENSIONS
PACKING AND ACCESSORY LIST
2 4
m
0 m
4
20
mm
1
3
0
m
m
Ø100mm
Ø
3
3
7
m
m
115mm
INSTALL THE PRODUCT
Housing Assembly
Duct Connector
Glass Shade
PE Bag
Manual, Pass Card,
Screws
T4x20
（
2pcs
）
EPS
Accessory
Tube,
Washer
Threaded
Carton
Carton
Glass filler 2
Glass filler 1
Light Fitting
Filler
(2pcs)
Carton
42W Halogen Lamps(2pcs),
Two Gang Switch
PE Bag
Light
Base
Glass Shade
Halogen Lamps(2pcs)
Washer
Motor
Plate
SERVICE
PARTS
Glass Shade
Washer
Halogen Lamps(2pcs)
Light Fitting Bracket
Duct Connector
Connecting Bracket
Product packing list is shown below
.
Please check when you open the carton. If there is any
questions, please contact the distributor or service center.
5.
Connect the light fitting electrical cable with
the plug provided. Using the threaded tube and
washer fix the light base to the light fitting
bracket. Install halogen lamps. Finally use
claws of light base to secure the glass shade.
6. Connect wire to relevant fuctions shown on
the switch.
Two Gang Switch
FAN
LIGHT
Switch Wiring Diagram
Threaded Tube
Light Base
Plug
Threaded Tube
Light Base
claw (3pcs)
Cardboard
1.
.
Use cardboard template to mark the correct
cut out size on the ceiling
2.
Connect the flexible duct to the duct
connector using tape or ties. Ensure the
flexible duct is installed as straight as
possible. Insert duct connector into
connecting bracket and fix to ceiling using
screws (T4 x 20).
3.
Remove the electrical connection box cover.
Insert the cables through the bush provided
and connect as indicated on the wiring
diagram ensuring the cables are captured
under the terminal screw. Replace cover.
Cut Out Size: 212mmx212mm
Duct
Connector
Connecting Bracket
Connecting Bracket
Screws T4x20
(
2pcs
)
Ceiling
Flexible
Duct
Housing
Assembly
Connect Place
Push In
Cover
4.
Fix the long screw (#10-24) tightly onto the light
fitting bracket. Clip both sides of the light fitting
bracket under slots in fan housing assembly.
Use the short screw (#8-18) to fix bracket
securely.
Light Fitting Bracket
Long Screw #10-24
o
t
nI
e
dil
S
o
t
nI
e
dil
S
Light Fitting Bracket
Short Screw #8-18
Ceiling
Cables
Terminal Screw
Cables
Slots
Cardboard
Installation work must be
done by a qualified person
and installed securely.
Electrical wiring must be
done in accordance with all
appliance standards.
Convenient installation and
service
Install this unit in a flat
ceiling only.
Prevent water backflow
.
Please keep access opening.
Avoid the following cases of duct installation.
Provide suction hole(s).
The duct pipeline vented to
the outdoors
must be
oblique,
preventing
rain
or
frost backflow.
Duct
In Room
Outdoor
Angle
Do not install in a place with
fumes and steam.
Housing and motor doesn’t
touch other ceiling
structure.
Prevent vibration and noise
Less than
Around temperature
40
℃
Above
50cm
The distance between fan
grille and floor must be
more than 2.3 meters.
Prevent accident
＞
2.3m
Do not install in a place with
high temperature.
C
A
U
T
IO
N
Do not use to exhaust hazardous or explosive materials.
When the product is connected to the power using a special power outlet, the plug and power outlet must meet the
requirements of AS3000. The power outlet must be rated at 10 amps and ensure a reliable earth/ground connection.
Install the product adjacent to the power outlet.
Mount the fan or fan/light switch to meet the requirements of AS3000.
A damaged power cord should only be serviced by a qualified electrician.
To avoid motor bearing damage and a noisy, unbalanced impeller, keep construction dust away from these parts.
Children should be supervised to ensure that they do not play with the appliance.
The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.
Do not immerse the product in water.
Ensure that the appliance is switched off from the supply mains all-pole disconnection switch before replace the lamps.
An all-pole disconnection switch shall be mounted between the mains supply and the wall switch of the appliance. The
all-pole disconnection switch shall have a contact separation in all poles, providing full disconnection from the mains
supply.
The appliance shall, under no circumstances, be covered with insulating matting and similar material.
