background image

MODELS EWT1306SS • EWT1366SS

Page 4

PREPARE THE HOOD 

(

cont

d

)

For ducted installation only:

Install both damper flaps inside the blower exhaust opening, 
ensuring the pins are top oriented. See illustration below.

HJ0225

P

ins

 

on

 

toP

1. GROUNDING INSTRUCTIONS
  This appliance must be grounded. In the event of an electrical 

short circuit, grounding reduces the risk of electric shock 
by providing an escape wire for the electric current. This  
appliance is equipped with a cord with incorporated 

 

grounding wire with a grounding plug. The plug must be 
plugged into an outlet that is properly installed and grounded.

 

NOTE:

  A recessed “clock” outlet is recommended.

2. Position the electrical outlet within the space covered by 

the decorative flue and where it will not interfere with the 
round duct. Make sure the outlet does not interfere with the 
mounting bracket fastening area, ductwork, or where the 
decorative flue touches the wall. 

INSTALL THE WIRING

4”

21”

12”

LOCATE

ELECTRICAL

OUTLET

WITHIN THESE

AREAS.

(Verify location

will not interfere

with duct,

mounting

brackets,

and flue.)

8.

8.

IMPORTANT!

Содержание EWT1306SS












Отзывы: