Broan ERV90HC Series Скачать руководство пользователя страница 9

Страница: 9 / 52

3. INSTALLATION

3.1 I

NSPECT

THE

ONTENTS

THE

• Inspect the exterior of the unit for shipping damage. Ensure that there is no damage to the door, door latches, power cord, etc.

• Remove and discard both transport brackets (

) and open the door. Discard the styrofoam

fillers (ERV units only) and remove the hardware kit from the unit. Inspect the interior of the
unit for damage. Ensure that heat or energy recovery core, core filters, insulation, dampers,
etc. are all intact.

3.2 L

OCATING

THE

NIT

Choose an appropriate location for the unit.

• Within an area of the house where

the ambient temperature is kept between 18°C (65°F) and 40°C (104°F)

(basement, furnace room, closet, etc.)

• So as to provide easy access to the interior of the unit, for maintenance.

• Close to an exterior wall, so as to limit the length of the insulated flexible duct to and from the unit.

• Away from hot chimneys and other fire hazards.

• Allow for a power source (standard 3-prong grounding outlet).

• For HRV units ONLY: Close to a drain. If no drain is close by, use a pail to collect run-off.

3.3 U

NIT

REPARATION

Both HRV and ERV units are equipped with 2 ports having integrated balancing damper. Turn the thumb
screw (

)

clockwise

to manually open and adjust the damper (

HRV

UNITS

: Set the Fresh air to building port to wide open position, and adjust the Exhaust air to outside port

to 3rd notch.

NOTE: If the unit needs to be balanced, adjust the damper of the Exhaust air to outside port to wide open

position. See Section 7.

ERV

UNITS

: Set both Fresh air to building port and Exhaust air to outside port to wide open position.

VD0183

VJ0032

Port with integrated balancing

damper - Top view

The door latches location can be changed from sides to front of the unit, according to the installation needs.

To do so, turn the unit upside down. Open the latches an unscrew them from the unit. Install the latches on their new locations.

VD0176

Latches on sides of the unit

Latches in front of the unit

VB0094

VO0089

VO0090

Содержание ERV90HC Series





















































Результаты поиска

Содержание ERV90HC Series

Отзывы:

Похожие инструкции для ERV90HC Series

Бренды по названию

Популярные бренды

Broan ERV90HC Series, Руководство по установке

Результаты поиска

Содержание ERV90HC Series

Отзывы:

Похожие инструкции для ERV90HC Series

Бренды по названию

Популярные бренды