Broadcom NetXtreme BCM57 Series Скачать руководство пользователя

Страница: 145 / 174

iSCSI Protocol and Broadcom Boot Agent Software

NetXtreme

User Guide

Broadcom

April 2017 • 2CS57XX-CDUM514-R

Page 145

Enabling CHAP Authentication

Ensure that CHAP authentication is enabled on the target.

To enable CHAP authentication

From the

General Parameters

screen, set

CHAP Authentication

Enabled.

From the

Initiator Parameters

screen, type values for the following:

• CHAP ID (up to 128 bytes)
• CHAP Secret (if authentication is required, and must be 12 characters in length or longer)

Select

ESC

to return to the

Main

menu.

From the

Main

menu, select

1st Target Parameters

From the

1st Target Parameters

screen, type values for the following using the values used when

configuring the iSCSI target:

• CHAP ID (optional if two-way CHAP)
• CHAP Secret (optional if two-way CHAP, and must be 12 characters in length or longer)

Select

ESC

to return to the

Main

menu.

Select

ESC

and select

Exit and Save Configuration

Configuring the DHCP Server to Support iSCSI Boot

The DHCP server is an optional component and it is only necessary if you will be doing a dynamic iSCSI Boot
configuration setup (see

Dynamic iSCSI Boot Configuration

Configuring the DHCP server to support iSCSI boot is different for IPv4 and IPv6.

•

DHCP iSCSI Boot Configurations for IPv4

•

DHCP iSCSI Boot Configuration for IPv6

DHCP iSCSI Boot Configurations for IPv4

The DHCP protocol includes a number of options that provide configuration information to the DHCP client. For
iSCSI boot, Broadcom adapters support the following DHCP configurations:

•

DHCP Option 17, Root Path

•

DHCP Option 43, Vendor-Specific Information

DHCP Option 17, Root Path

Option 17 is used to pass the iSCSI target information to the iSCSI client.

The format of the root path as defined in IETC RFC 4173 is:

"iscsi:"<servername>":"<protocol>":"<port>":"<LUN>":"<targetname>"

The parameters are defined below.

Содержание NetXtreme BCM57 Series















































































































































































Результаты поиска

Содержание NetXtreme BCM57 Series

Отзывы:

Похожие инструкции для NetXtreme BCM57 Series

Бренды по названию

Популярные бренды

Broadcom NetXtreme BCM57 Series, Руководство пользователя

Результаты поиска

Содержание NetXtreme BCM57 Series

Отзывы:

Похожие инструкции для NetXtreme BCM57 Series

Бренды по названию

Популярные бренды