Broadcom NetXtreme BCM57 Series Скачать руководство пользователя

Страница: 142 / 174

iSCSI Protocol and Broadcom Boot Agent Software

NetXtreme

User Guide

Broadcom

April 2017 • 2CS57XX-CDUM514-R

Page 142

•

iSCSI parameters via DHCP

: Disabled

•

CHAP Authentication

: Disabled

•

Boot to iSCSI target

: Disabled

•

DHCP Vendor ID

: BRCM ISAN

•

Link Up Delay Time

: 0

•

Use TCP Timestamp

: Enabled (for some targets such as the Dell/EMC AX100i, it is necessary to

enable

Use TCP Timestamp

)

•

Target as First HDD

: Disabled

•

LUN Busy Retry Count

: 0

•

IP Version

: IPv6. (For IPv6)

Select

ESC

to return to the

Main

menu.

From the

Main

menu, select

Initiator Parameters

From the

Initiator Parameters

screen, type values for the following:

• IP Address (unspecified IPv4 and IPv6 addresses should be “0.0.0.0” and “::”, respectively

)

• Subnet Mask Prefix
• Default Gateway
• Primary DNS
• Secondary DNS
• iSCSI Name (corresponds to the iSCSI initiator name to be used by the client system)

Select

ESC

to return to the

Main

menu.

From the

Main

menu, select

1st Target Parameters

From the

1st Target Parameters

screen, enable

Connect

to connect to the iSCSI target. Type values for

the following using the values used when configuring the iSCSI target:

• IP Address
• TCP Port
• Boot LUN
• iSCSI Name

Select

ESC

to return to the

Main

menu.

Select

ESC

and select

Exit and Save Configuration

10.

Select

to save your MBA configuration.

Dynamic iSCSI Boot Configuration

Note:

Carefully enter the IP address. There is no error-checking performed against the IP address to

check for duplicates or incorrect segment/network assignment.

Содержание NetXtreme BCM57 Series















































































































































































Результаты поиска

Содержание NetXtreme BCM57 Series

Отзывы:

Похожие инструкции для NetXtreme BCM57 Series

Бренды по названию

Популярные бренды

Broadcom NetXtreme BCM57 Series, Руководство пользователя

Результаты поиска

Содержание NetXtreme BCM57 Series

Отзывы:

Похожие инструкции для NetXtreme BCM57 Series

Бренды по названию

Популярные бренды