Britax ISOFIX COMPATIBLE Скачать руководство пользователя страница 35

Страница: 35 / 92

Instructions for Installation & Use

Step 5.

Connect the ISOFLEX

connectors into

each ISOFIX low anchorage.

Give a firm tug on the connector to

check it is securely fitted. Connectors
may also show a green indicator on
top.

Step 6.

With the child seat in position, apply

firm pressure whilst pulling on adjuster
strap to remove all slack and tighten
the ISOFLEX® strap. Repeat on the
other side of the restraint. The two
tension indicators will show green
indicating minimum tension has been
applied.

Step 7.

You have now successfully completed

the ISOFLEX

installation and are now

ready to install the top tether. Please
go to page 36.

You do not need to seatbelt install with
ISOFLEX

SETUP -

ISOFLEX

FOR

REARWARD FACING

IMPORTANT:

Do not attach the lower attachment connectors of two separate child restraints to

the same ISOFIX low anchorages in your car.
Always attach the top tether strap to the child restraint upper anchorage in your car.

ENSURE THERE ARE NO TWISTS IN

ISOFLEX

CONNECTOR STRAPS.

ALWAYS REMOVE SLACK FROM

ISOFLEX

STRAPS.

A LOOSE INSTALLATION IS DANGEROUS.

Содержание ISOFIX COMPATIBLE





























































































Результаты поиска

Содержание ISOFIX COMPATIBLE

Отзывы:

Бренды по названию

Популярные бренды

Britax ISOFIX COMPATIBLE, Инструкция по эксплуатации

Результаты поиска

Содержание ISOFIX COMPATIBLE

Отзывы:

Бренды по названию

Популярные бренды