Britax FORWARD FACING CHILD RESTRAINT Скачать руководство пользователя страница 7

HOW  TO  INSTALL

7

TO  REMOVE  RESTRAINT  FROM  VEHICLE

A.

B.

C.

Disengage seat belt tongue from buckle and remove from restraint.

Fully press Upper Anchorage Strap Adjuster Button (A) 
while pulling Upper Anchorage Strap (B) to slacken as 
shown right. In some vehicles loosening of the Upper 
Anchorage Strap may be difficult. If so, try pushing the 
restraint against the vehicle seat back or slightly lifting 
the restraint to release the tension.

Disengage Attachment Clip from Anchor Fitting. The 
child restraint is now disconnected.

Pull Adjustment Strap
to remove slack

Storage
Strap

Fully press Adjuster Button (A)
while pulling Upper Anchorage
Strap (B) to lengthen.

A

B

HOW  TO  CLEAN

14

Shoulder

Strap Slots

Harness

Adjustment

Strap

The restraint has a flame retardant cover which is removable for cleaning. Cleaning instructions 
are on the care label attached to the cover. If fluffy cover is fitted then washing cover prior to use 
will remove excess fluff. 

Ensure that the inside of the buckle is free of foreign matter.

 Cleaning 

instructions are on page 15. Use only mild soap and water to clean all metal and plastic parts of 
the restraint.

Remove the restraint from vehicle as instructed on page 7.

Disengage harness tongues from harness buckle.

Remove any accessories, if fitted as instructed on page 16.

Disengage harness straps from harness Strap Connector as instructed on page 13, item C.

  Unhook the cover at the top and bottom of the restraint. Peel cover from outer rim of the body 

starting from       on both sides and then at       , at the top.

Remove the cover while feeding the Harness Tongues & Crotch Buckle through the lap strap 
slots in the cover.

Feed the Harness straps and Harness Tongues 
through Lap Strap Slots and through matching 
shoulder strap slots in the cover and seat.

Stretch cover over the top of the restraint first at       ,       
then the sides at       , as instructed above and then 
stretch the cover around the rim of the restraint. 

Re-fit the Seat Cover attachments.

Re-engage harness straps to Harness Strap Connector 
as instructed on page 13, item E to G.

Feed Crotch Buckle through slots in cover.

The cover has been designed to protect your child when 
seated in the restraint. Care should be taken if children 
either eat or drink while in the restraint as some food or 
drink products may cause damage or marking to the cover.

 

TO  REMOVE  COVER:

TO  REPLACE  COVER:

A.

B.

C.

D.

E.

F.

A.

B.

C.

D.

E.

COVER 

(STYLE MAY VARY)

Do not

 remove Harness Adjustment Strap from Harness Adjustment Strap Lock.

IMPORTANT:

Do not pull sticky items from covers as the 

cover may be damaged - soak in water and gently remove.

Cover Hooks

Содержание FORWARD FACING CHILD RESTRAINT











Отзывы: