manualshive.com logo in svg

Britannia K7088ASC - 70, Инструкция пользователя, Страница: 4 / 8

Поделиться
Скачать
Britannia K7088ASC - 70 Скачать руководство пользователя страница 4

Installation

Height above hotplates

For best performance we suggest that the hood is installed at a distance between 65cm to75cm from
the hotplate surface. Under no circumstances should the hood be installed lower than 65cm above the
hotplate surface.

Ducting information

This hood is designed for ducting out, i.e. duct to an outside wall.To obtain the best possible extraction
performance use 150mm diameter ducting.Wherever possible utilise rigid circular pipe or “Mega duct”
ducting - both types are available via your Britannia dealer. Do not use expanding concertina type
ducting as this is not smooth on the interior and can cause air flow restrictions. Do not use ducting
that has a smaller diameter than 150mm as this will reduce extraction rates and can increase noise
levels. Please note ducting kits and ducting components are optional accessories and have to be ordered
- they are not supplied with the hood.

Maximum length of ducting run

4 metres with 1 x 90 degree bend

3 metres with 2 x 90 degree bends

2 metres with 3 x 90 degree bends

Note: the shorter the ducting run and the least number of bends gives the best extraction performance.

Warning: Any ducting used must be fire retardant.

Unpacking the hood

On some models components are packed inside the polystyrene protection pieces.

Do not throw away the box and packaging until installation is fully completed.

Installation

ATTENTION:
The appliance should be installed by a qualified electrician or competent person.

1

Before fixing the hood install the ducting run for air evacuation to the outside. See fig. 1 . Ducting can
be run through the rear wall or through the ceiling.

2

Turn off electricity before preparing a suitable power supply. For the electrical connection requirements
follow the details on page 2.

3

Remove the metal grease filters. See fig. 2

3

90 degree bend

Code DUCT/690

Pipe connector

Code DUCT/693

One metre
ducting kit

Comprising: one
metre length pipe,
wall vent and 90
degree bend.

Code DUCT/2609

One metre
length pipe

Code DUCT/1100-6

Two metre
length pipe

Code DUCT/1200-6

One metre and two
metre length pipes can be
cut to the desired length

Wall vent with
gravity flaps

Code DUCT/6900

Combination of 6” (150mm) circular
pipe and flat channel (220mm x 90mm)
which is ideal for running on top of
wall units or between ceiling joists.

Megaduct kit 

Code DUCT/2652B

Horizontal bend

Code DUCT/950

Megaduct Ducting Kit

horizontal
bend

350

1000

1000

1000

Содержание K7088ASC - 70









Отзывы:

Нет отзывов