background image

66

7

The installation must comply with all Water and Building 

Regulations (England) and Water By-laws (Scotland).
If the shower is to be installed in a hard water area, we recommend 

that an in-line scale inhibitor is fitted which will prolong the life of 

the shower. Please refer to your supplier for advice.

Warning: The shower must not be installed in an area subject 

to freezing conditions. Do not use if you suspect the shower is 

frozen, this will damage the shower unit.
The shower must be connected to a mains water supply only 

with a minimum working inlet pressure of 0.07MPa (0.7bar) at a 

minimum flow rate of 8 litres per minute. The maximum static 

inlet pressure must not exceed 1.0MPa (10bar). 

If it is intended to operate the shower at pressures above the 

maximum stated, a suitable pressure reducing valve (PRV) should 

be used.
Water regulations stipulate that the showerhead be ‘constrained 

by a fixed or sliding attachment (hose retainer) so that it can only 

discharge water at a point not less than 20mm above the spill over 

level of the bath or shower tray or other fixed appliance’.
If a showerhead can sit within a bath, basin or shower tray, you 

must fit a double check valve in the supply pipe work to prevent back 

siphonage. If the showerhead can sit within a WC then the air gap 

should be a type AUK3 not less than 20mm or twice the diameter of 

the inlet pipe to the fitting, whichever is the greater.

Pressure Relief Device (PRD)

A pressure relief device is designed into this shower. The pressure 

relief device provides protection should an excessive build up of 

pressure occur within the shower unit. It is advisable to position 

the shower unit over a bath or shower tray in the unlikely event the 

device should discharge.
Do not use the shower with a damaged or kinked shower hose or 

blocked handset. This may trigger the PRD which will discharge 

through the vent in the bottom right hand corner (shown).  
In the event of the PRD activating, water will be discharged from the 

vent. If this happens, switch off the electricity and water supplies to 

the shower and contact Customer Services (see page 19).

Water Requirements

Double pole

switch

Shower 

unit

Shower tray

spillover level

Bath spillover

level

Hose

retainer

Minimum 20mm

between 

showerhead

and spillover

1m minimum 

height from 

shower unit

to floor

PRD Vent

Need help?

 Give us a call on

 0844 701 6273

 and speak to one of our trained advisors.  

Содержание SM385 W

























Отзывы: