Brinly STS-427LXH Скачать руководство пользователя страница 9

Страница: 9 / 28

================================================================================================

1009725-E

ASSEMBLY

STEP 5

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

STEP 6

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Loosely add the Bolt (13) &

Lock Nut (21) from

PANEL 04

to the Height Adjustment

Handle (2).

Pointing the Nut side out,

slide the Height Adjustment

Handle (2) into place against the

Lower Pivot (43) side plate.

Use the head of Bolt 13
to hold in place.

TIGHTEN

HARDWARE

SECURELY.

NOTE:

The large hole

in bottom of the Height

Adjustment Handle (2) must fit over the Tube

extending past the Lower Pivot (43) side plate.

FIRST

- Run Bolt (27) through the Left Tow Bar (4)

using the following hardware from

PANEL 05

in the order listed below:

• Hex Bolt (27)

• 5/16” Washer (19)

• Left Tow Bar (4)

• 5/16” Washer (19)

• 5/16” Lock Washer (18)

• 5/16 Hex Nut (16)

• TIGHTEN HARDWARE SECURELY

SECOND -

Adding on to the same bolt (27), attach

the Lock Arm (1) using hardware in this order:

• Hex Bolt (27)

• 5/16” Washer (19)

• Lock Arm (1)

• 5/16” Washer (19)

• Nylon Lock Nut (25)

Note:

Do not over tighten the Nylon Lock Nut

(25).

The Lock Arm (1) should be able to pivot freely after

assembly.

LAST

- Slide the Vinyl Bolt Cap (7) over the end of the Bolt (27).

Note: Wheel assembly

not shown for clarity.

First

Second

Last

Содержание STS-427LXH





























Результаты поиска

Содержание STS-427LXH

Отзывы:

Похожие инструкции для STS-427LXH

Бренды по названию

Популярные бренды

Brinly STS-427LXH, Руководство пользователя

Результаты поиска

Содержание STS-427LXH

Отзывы:

Похожие инструкции для STS-427LXH

Бренды по названию

Популярные бренды