background image

Pa

g

e

 9

CAUTION

DEEP

 TILL

 OPERA

T

ION CAN DAMAGE

UNDERGROUND UTILITIES CAUSING

DANGEROUS CONDITIONS 

AND

DISRUPTING SER

VICES.  DETERMINE

THE DEPTH 

AND LOCA

TION OF BURIED

CABLES, PIPE LINES, 

AND DRAIN

TILES BEFORE OPERA

TION.

8K829

B

r

illion

B

r

illion

On Rear Frame 

Between Shanks

5

 

1. DO NOT

 LUBRICA

TE, 

ADJUST

 OR REP

A

IR WHEN MACHINE IS IN MOTION.

 

2. DO NOT

 T

OW OR 

TRANSPOR

T

 F

ASTER 

THAN 15 MILES PER HOUR.

 

3. DO NOT

 RIDE OR 

ALLOW OTHERS 

T

O

 RIDE ON 

THE MACHINE.

 

4. 

BLOCK UP

 ALL

 HYDRAULICALL

Y

 OR MECHANICALL

Y

 RAISED COMPONENTS 

T

O

 

 

PREVENT

 UNINTENDED LOWERING OR LOWER 

THE MACHINE 

T

O

 THE GROUND 

T

O

 

 

MAKE 

ADJUSTMENT

  OR REP

A

IRS WHEN NOT

 IN USE.

 

5. KEEP

 ALL

 PERSONS 

A

W

A

Y

 FROM MACHINE DURING HITCHING 

AND OPERA

TING.

 

6. SLOW DOWN BEFORE MAKING SHARP

 TURNS OR USING 

THE BRAKES.

 

 

DRIVE SLOWL

Y

 OVER ROUGH GROUND, SIDE HILLS, 

AND 

AROUND CUR

VES 

T

O

 A

V

OID  

......

  

TIPPING.

 

7. COMPL

Y

 WITH 

ALL

 LA

WS WHEN 

TRANSPOR

TING 

THE MACHINE ON PUBLIC ROADW

A

YS.

 

8. INSTRUCT

 ALL

 OPERA

T

ORS IN 

THE SAFE OPERA

TION OF 

THE MACHINE.

 

 

REVIEW 

THE OPERA

T

OR’S MANUAL

 FOR CORRECT

 PROCEDURES.

 

9. BLOCK IMPLEMENT

 T

O

 PREVENT

 MOVEMENT

 WHEN UNHITCHED FROM 

TRACT

O

R.

10. 

KEEP

 ALL

 GUARDS 

AND SHIELDS IN PLACE WHILE MACHINE OR P

A

R

T

ARE IN MOTION. 

CAUTION

C

ompaction

   

 C

ommander

 7

 8

 4

 3

 4

 2

 1

9K308

604

Page  7

SPRING UNDER LOAD

DO NOT

 DISASSEMBLE WITHOUT

 USE OF

SER

VICE 

T

OOL& FOLLOWING PROCEDURE

OUTLINED IN OPERA

T

OR’S MANUAL.

SPRING IS LOADED 

AND IMPROPER

REMOV

A

L

 OF BOL

T

S COULD RESUL

T

 

IN SERIOUS INJUR

Y

.

2K762

W

ARNING

Содержание Compaction Commander 03 Series



































Отзывы: