Brillion BOS4F Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 48

background image

7K116

4.

Seed Meters:

Alignment -

1. Loosen appropriate adjusting nut.

2. Using the opposite shaft adjusting

nut, pull the shafts so that the meters
are closed.

Do not overload the

meters against the seed cups by
pulling the shaft too far.

3. Check to make sure that all the meters

are closed.

If not, Loosen the bolts,

that mount seed cups to the box and
reposition the seed cup so that it is
closed.

4.

Check to make sure that the spring
pointer indicates “

0

” on the seed

shaft decal.

Reposition pointer if

needed.

5. Using the appropriate seed shaft nut,

adjust the seed shaft so that the
indicator points to “

2

”.

Make sure

that all seed meters are open the
same amount. If not, repeat the
steps above.

6. This procedure is used on both seed

boxes if your overseeder is equipped
with two boxes.

Page 13

OUTER
ADJUSTING
NUT

POINTER

Decrease:

shaft moves this

direction

Increase:

shaft moves this

direction

Figure 7

FRONT

of Machine

INNER
ADJUSTING
NUT

345678

01 2 3 4567 8

900rev7-11-03

«
...
13
14
15
16
17
...
»

Содержание BOS4F

















































Отзывы:

Нет отзывов

Похожие инструкции для BOS4F

Бренд: Abicor Binzel Страницы: 92

Thiele Technologies Streamfeeder Reliant...

Бренд: Barry-Wehmiller Страницы: 72

Бренд: Cumberland Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды