background image

Reading the LED Display

Figure 7

Fixture Status Indicator

DMX Signal Indicator

Channel Indicator

Adjustment
Buttons

Note: Fixtures are supplied with onboard memory capabilities that retain the fixture’s last setting.

1. The channel indicator is used to determine the setting of the fixture in the following modes:

a) Emergency On Mode:

 Fixture is manually operating at 100% 

b) Manual Dimming Mode:

 Fixture is

manually dimmed at LED display without the use of a lighting control console. 

c) Console Dimming Mode:

Fixture is set to a DMX address for dimming by the use of a  lighting control console. Use Table 2 to evaluate

the readout of the channel indicator on the LED display (Figure 7).

2. The DMX signal indicator is used to determine whether the fixture is receiving a DMX signal while in the

Console Dimming Mode

. The lighting control console and all necessary DMX cabling must be installed. Use

Table 3 to evaluate the readout of the DMX signal indicator on the LED display (Figure 7).

3. The fixture status indicator is used to determine whether the changes being made to the settings at the LED

display are completely processed. Use (Table 4) to evaluate the readout of the fixture status indicator on the
LED display (Figure 7). Any changes made to the settings will require a few seconds to be processed.

Table 2

Table 3

Table 4

DMX Signal Indicator

DMX Signal Status

DMX LED Off

No Signal

DMX LED On

Unuseable Signal

DMX LED Flashing

Signal OK

Channel Indicator

Description

000 Emergency ON/Fixture at 100%

001-512 DMX Address for Lighting Control Console

513-899 Not Available

900-999 Manual Dimming (1% Increments, 900 = OFF, 925 = 25%, etc.)

Fixture Status Indicator

DMX Signal Present

Emergency On/Manual Dimming

Run LED Off

Processing Changes to Settings

Processing Changes to Settings

Run LED On

Settings completely processed

Not Available

d

e

s

s

e

c

o

r

p

 

y

l

e

t

e

l

p

m

o

c

 

s

g

n

i

t

t

e

S

e

l

b

a

li

a

v

A

 

t

o

N

g

n

i

h

s

a

l

F

 

D

E

L

 

n

u

R

10

Содержание BL.16
















Отзывы: