Breezy Breezy Premium, Руководство пользователя

Страница: 14 / 84

14 BREEZY PREMIUM
ENGLISH
Castors, castor plates, forks
The wheelchair may veer slightly to the right or left, or the castors
may wobble. This may be caused by the following:
• Forward and/or reverse wheel motion has not been set properly.
• The castor angle has not been set correctly.
• Castor and/or rear wheel air pressure is incorrect; the wheels do
not turn smoothly.
The wheelchair will not move in a straight line if the castors have not
been properly adjusted. Castors should always be adjusted by an
authorised dealer. The castor plates must be re-adjusted, and the
wheel locks must be checked every time the rear wheel position has
been altered.
The seat height is determined by the castor and rear wheel position.
The seat height can be adjusted by altering the position of the rear
wheels and the castors (see seat height matrix on page 14).
CAUTION!
After adjusting the seat height, all screws must be re-tightened and
the wheel lock must be readjusted.
Options - Castors
Options - Rear Wheel Extension
Fig. 14.0
Options - Backrest
Position of the rear wheel extension
(Fig. 13) The rear wheel extension
can be fitted behind the back tube
for greater security against tipping
over. The larger the wheelbase the
greater security against your
wheelchair tipping over.
CAUTION!
Wheel locks must be adjusted to
match the new position!
CAUTION!
• Keep hands clear of the
adjustment mechanism
between, the frame and the
movable parts of the footrest
while elevating or lowering the
footrest.
• The footrests should not be used
to lift or to carry the wheelchair.
• Risk of trapping fingers!
• When moving the footrest up or
down, do not put your fingers in
the adjusting mechanism
between the moving parts of the
footrest.
• When getting on or off the
wheelchair, do not use the
footboards.
These should be flipped up beforehand or the footrest should be
swung to the outside as far as possible.
Adjusting the calf pad
The calf pad can be adjusted as follows:
Height: Open bolt (4 Fig.12.0) and move the clamping piece to the
desired position. By rotating the clamping piece also the angle can
be adjusted.
Width: Open bolt (5) and rotate the position of the plastic part behind
the pad, to get the desired position.
CAUTION!
Always make sure that the fasteners are secure.
Make sure that the legrest is locked into place correctly, (Fig. 9.0).
Option Elevating Legrest
(Fig. 10.0-13.0)
To remove, pull the lever (1), swing
the footplate outwards and then lift
the legrest out.
Height Adjustment :
The lower leg length can be
adjusted by releasing the screw
(2). Adjust the suitable height and
tighten the screw again.
CAUTION!
The distance between the foot -
plate and the ground must be at
least 40 mm.
Angle Adjustment:
Press the lever (3) downward with
one hand while supporting the
legrest with the other hand to take
the load off. When a suitable
angle is achieved, let go of the
lever and the legrest will lock into
one of the preset positions.
Fig. 10.0
1
Fig. 11.0
Fig. 12.0
4
2
3
Fig. 13.0
5
Half folding back
Unfolding the backrest:
To put the backrest in the upright
position, push the handles
upwards and forwards until they
lock in, (Fig.15).
WARNING!
Keep fingers and other items away from the folding mechanism
when the backrest is being folded to prevent injury or damage
to property.
Folding the backrest:
The backrest can be folded to make storage of the wheelchair
easier, (Fig.16).
CAUTION!
Do not operate under load as
this may cause lever to break.
To fold the backrest, stand behind
the wheelchair, press the two
small levers positioned on each
side of the backrest (just above
the armrests). Fold the backrest down.
Fig. 16.0
Fig. 15.0
1
1