background image

Ussc 

15

OUTSIDE COMBUSTION AIR

For air tight houses and houses with negative pressure problems, your wood stove must have a fresh air intake 
installed. You can either purchase a dryer venting kit from your local hardware supply or cut a hole in the 
fl ooring protector and home’s fl oor as shown in the illustration at the beginning of this manual.

Outside combustion air may be required if :

1.  Your stove does not draw steadily, smoke rollout occurs, wood burns poorly, or back-draft s occur whether 

or not there is combustion present.

2. Existing fuel-fi red equipment in the house, such as fi replaces or other heating appliances, smell, do not 

operate properly, suff er smoke roll-out when opened, or back-draft s occur whether or not there is combustion 
present.

3.  Opening a window slightly on a calm (windless) day alleviates any of the above symptoms.

4. Th

  e house is equipped with a well-sealed vapor barrier and tight fi tting windows and/or has any powered 

devices that exhaust house air.

5. Th

  ere is excessive condensation on windows in the winter.

6.  A ventilation system is installed in the house.

Illustration: Optional securing of heater to the Floor.

NONCOMBUSTIBLE FLOORING

Содержание SW4100

























Отзывы: