Brave VH1322GC Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 48

background image

Assembly Instructions

Brave

14

800-350-8739

17

. Attach high-pressure hose (A) to the

bottom valve fitting.

NOTE:

The high-pressure hose is self-

sealing and does not require any type of
sealing material. Tighten the fitting with

the 10 inch crescent wrench.

18

. Attach the end of low-pressure return

hose (B) to the fitting on top of the valve.
Position and tighten the hose clamp
approximately 3/8 inch from the end of the

hose.

NOTE:

Steps 19 and 20 apply to

installation of fenders on model VH1326
only.

19

. Install the left and right-hand fender

brackets using two 5/16-18 x 3/4 inch long
hex head bolts and locknuts for each
bracket. Install the bracket with the
slotted holes against the base unit (round
holes up).

NOTE:

The right-hand side of the log

splitter is the right side when viewed from
the hitch end.

20

. Bolt the fenders onto the fender brackets

using  two  5/16-18  x  3/4  inch  long  hex
head bolts and locknuts.  The fenders are
interchangeable  (left  or  right).    Position
the fender with the bolts in the middle and
front holes.  This should place the fender
over  the  tire  with  equal  spacing  in  the
front and back.

«
...
14
15
16
17
18
...
»

Содержание VH1322GC

















































Отзывы:

Нет отзывов

Похожие инструкции для VH1322GC

Бренд: TOPMAQ Страницы: 21

Бренд: Brave Страницы: 62

Бренд: Yardworks Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды