manualshive.com logo in svg

Brave PCLS1513, Руководство пользователя

Поделиться
Скачать
Brave PCLS1513 Скачать руководство пользователя страница 17

800-350-8739 

15

Brave

 

 

Start-up Procedure

 

 

Important Notice

 

Read the Engine’s Operating & Maintenance Instructions and follow the instructions 
listed below before starting or operating your log splitter. Failure to do so may result in 
engine and hydraulic pump damage. 

 

NOTE:  

Place a clean container under oil level hole to catch any overflow of oil. Do not 

allow excess oil to spill onto the ground. 

 

1

.  Remove the fill cap and oil level screw 

from the oil tank. Using a long-neck 
funnel,   SLOWLY   pour,   approximately 
6 quarts (5.7 liters) of the selected oil into 
oil fill opening (K) until it flows from oil 
level hole (L). Do not mix fluids, use only 
one type.   Re-install the fill cap and oil 
level screw. 

 

Hot weather - SAE  30W  or  AW  68  tractor 

hydraulic oil 

 

Cold weather - SAE 10W or AW 32 tractor 

hydraulic oil or Dexron VI, 
Mercon V or Equivalent auto- 
matic transmission fluid. 

 

NOTE: 

The total hydraulic oil capacity for this 

unit is 9 quarts (8.5 liters). The remaining 3 
quarts (2.8 liters) of oil will be added in Step 8. 

 

 

2

.  Lubricate the underside edges of the rail 

with clean grease. This will help to prevent 
wear between the slide plates and the rail. 

 

3

. Fill the engine’s crankcase with the 

engine manufacturer’s recommended oil. 
Pour slowly and fill to the manufacturer’s 
recommended level. Refer to the Oil 
Chart in the engine manual for different 
viscosities and types of oil to use for 
different temperatures. 

 

NOTE: 

Various engines used on the EZ Split 

15 may have the oil fill at different locations. 
For more information on oil fill locations, refer 
to the engine manual. 

Содержание PCLS1513

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды