BraunAbility Century 2, Руководство по обслуживанию

Страница: 13 / 38

Page 11
Maintenance and Lubrication Schedule
Maintenance and
lubrication procedures
must be performed as
specified by an
authorized service
technician. Failure to
do so may result in
serious bodily injury
and/or property
damage.
Proper maintenance is necessary to ensure safe,
trouble-free operation. Inspecting the lift for any wear,
damage or other abnormal conditions should be a part
of the transit agency daily service program. Simple
inspections can detect potential problems.
The maintenance and lubrication procedures specified
in this schedule must be performed by a BraunAbil -
ity authorized service representative at the scheduled
intervals according to the number of cycles.
BraunAbility dual parallel arm lifts are equipped with
hardened pins and self-lubricating bushings to de -
crease wear, provide smooth operation and extend the
service life of the lift.
When servicing the lift at the recommended intervals,
inspection and lubrication procedures specified in the
previous sections should be repeated. Clean compo -
nents and the surrounding area before applying lubri -
cants. Clean only with water, and then when cleaned,
lubricate as directed in the lubrication diagram. Do not
use solvents to clean.
LPS2 General Purpose Penetrating Oil is recom -
mended where Light Oil is called out. Use of improper
lubricants can attract dirt or other contaminants which
could result in wear or damage to the components.
Platform components exposed to contaminants when
lowered to the ground may require extra attention.
Lift components requiring grease are lubricated during
assembly procedures. When these components are
replaced, grease must be applied during installa -
tion procedures. Specified lubricants are available
from BraunAbility (part
numbers provided on
previous page).
All listed inspection,
lubrication and main -
tenance procedures
should be repeated at
750 cycle intervals fol -
lowing the scheduled
4500 cycle maintenance
procedures. These
intervals are a general
guideline for scheduling
maintenance procedures
and will vary according
to lift use and conditions. Lifts exposed to severe con -
ditions (weather, environment, contamination, heavy
usage, etc.) may require inspection and maintenance
procedures to be performed more often than specified.
Cycle Counter: NCL-2 Series lift models are
equipped with a cycle counter located on the top of
the pump module. This cycle counter allows the lift
attendant/operator to easily track the number of cycles
during daily inspections of the lift.
Discontinue lift use immediately if maintenance and
lubrication procedures are not properly performed,
or if there is any sign of wear, damage or improper
operation. Contact your sales representative or call
BraunAbility at 1-800-946-7513. One of our Aftersales
representatives will direct you to an authorized service
technician who will inspect your lift.
Outer barrier pivot points (2)
Outer barrier latch pivot points (2)
Outer barrier switch lever pivot points (2)
Outer barrier latch roller bearing (2)
Outer barrier arm slots (2)
Outer barrier gas springs (2 springs - 4 points)
Lift-Tite
™
latches (tower pivot points - 2)
Lift-Tite
™
latch gas (dampening) spring pivot
points (2 springs - 4 points)
Inspect Lift-Tite
™
latches and gas (dampening)
springs for wear or damage (bent, deformed or mis -
aligned), positive securement (lock nuts / external
snap rings) and proper operation
Apply Light Oil - See Lubrication Diagram
Apply Light Oil - See Lubrication Diagram
Apply Light Oil - See Lubrication Diagram
Apply Light Oil - See Lubrication Diagram
Apply Light Grease - See Lubrication Diagram
Apply Light Oil - See Lubrication Diagram
Apply Light Oil - See Lubrication Diagram
Apply Light Oil - See Lubrication Diagram
Resecure, replace damaged parts or otherwise
correct as needed. Note: Apply Light Grease to
Lift-Tite
™
latch tower pivot point if replacing latch.
750
Cycles
WA RNING
continued