background image

 

3 SECURITY PRINCIPLES 

3.1

 

SECURITY

 

PRINCIPLES

 

OVERVIEW 

A hazard exists when handling movable parts of structures especially in the event that 
the  jack  is  not  use  in  the  right  way  or  is  badly  maintained.  Whereas  as  a  result  an 
accident  or  severe  injury  could  happen,  it  is  necessary  to observe  the  special  security 
measures when handling, assembling, maintaining and checking the jack. 
 

 !  VAROVÁNÍ 

ALWAYS 

ensure  the  raised  part  of  the  structure  against  drop  (e.g.  by  brace  rod),  if 
you intend to work under it. 

NEVER 

jack up persons. 

NEVER 

burden the jack more than is the load capacity indicated on the jack. 

ALWAYS 

warn persons in surroundings before starting work. 

ALWAYS 

read the operation manual and security instructions. 

Bear in mind that the operation staff is responsible for faultless technique of raising. 
Hence  verify  all  national  directives,  regulations  and  standards  whether  they  contain 
other information on safety work with your jack. 

 
3.2.

 

SECURITY

 

PRINCIPLES 

 !  WARNING 

3.2.1 Prior to use 
ALWAYS 

ensure  the  jack  would  be  operated  by  physically  fit,  qualified  and 
instructed  persons  older  than  18  years,  familiarized  with  the  operation 
manual and trained in security of work and mode of operation. 

 

ALWAYS 

check up the jack every day before starting work according to Section 8.2. 
(1) „Daily inspection“. 

 

NEVER

  

use the defective or outworn jack. 

NEVER 

use the jack without visible load capacity marking on the jack. 

NEVER 

use the jack marked with the label „

OUT OF OPERATION

“. 

ALWAYS 

consult the producer or his authorized representative any application of the 
jack in nonstandard or extreme environment. 

ALWAYS

 

check  that  the  product  is  grounded  through  the  ground  terminal  when 

working in an explosive atmosphere 

ALWAYS

 wipe off any dust before handling the product in an explosive atmosphere 

 

3.2.2 When in use 
ALWAYS 

make sure the jack is properly mounted in equipment construction. 

ALWAYS 

pay increased attention, if the jack is drawn up to maximum position. 

ALWAYS 

work with the jack only with manpower.  

ALWAYS 

we  recommend  with  respect  to  actuating  forces  the  jack  operation  is 
ensured  by  two  persons  when  handling  parts  of  structures  the  weight  of 
which approximate to safe working load of the hoister. 

Содержание 15-00-CON

















Отзывы: