BRAILLO
l
B 650 SF
116
Software Reset:
ESC 0
- Soft Reset
This command is used to reset the Printer. It is
used from the computer and has the same effect
as pushing the key RESET PRINTER. Software
Reset should be used with care: If the printer
has not finished printing, the rest of the text in
the buffer will be lost, and a new paper position
will be assumed by the Printer. Because of this,
the command is only to be used after a software
form feed has been executed, and the Printer has
stopped completely.
ASCII
HEX
Software Reset
027 048
1B 30
Software Form Feed:
ESC 1
- Soft Form Feed
This command is to be used after all text in one
volume has been transmitted to the Printer. If
text corresponding to less than two pages, or
text with an odd number of pages is received,
and not followed by FF on the last page, the
Printer will wait for more text or FF. This means
that the last page may be stuck in the Printer.
This is due to the double-sided printing of the
Printer. This command makes the Printer to start
printing the rest of the text. After this the paper
position will be the same as it had when this
volume of text was started. Then page no. 1 on
the next volume will start out correctly. There
will always be at least one blank sheet of paper
between the volumes of text when finishing
each volume with a Software Form Feed.
ASCII
HEX
Software Form Feed 027 049
1B 31
Printer ID:
ESC 4
- Adding the Printer ID
When you have several Braille Printers producing
the same Braille material, it is not always easy to
later figure out what Printer made which book. It is
therefore possible to add a Printer ID to the last line
on a sheet. There is no matter where the escape-
sequence is placed on the page, the ID will always
be printed on the last line. Meaning, if you send
this escape-sequence on the last page of every print
job, you will get the Printer ID printed on the last
line on the last page.
The Printer ID is a 5 digit code that has to be set
in the menu choice:
Main menu - Printer Setup
- Printer ID
. See figure below:
Содержание 650 SF
