Braillo 600 SR Скачать руководство пользователя страница 77

Страница: 77 / 119

BRAILLO

B 600 SR

4.16 Beam and sensor, adjustment

The Beam wheel sensor is placed on the lower shaft, on the opposite end from the belt.

Note that this adjustment has to be done with the shafts positioned like on the figure with the arrows

pointing towards each other. The notch on the beam wheel should now be placed exactly opposite the

sensor like in the figure below.

If the edge is not in it’s correct position, it must be adjusted.

Keep the shafts in this position while loosening the two screws holding the beam wheel. Turn the beam

wheel until the notch on the beam wheel is placed in the middle of inductive sensor. Then fasten the

two screws.

Keep the shafts in

this position

The notch must be

in the middle of the

sensor

Sensor

Содержание 600 SR
























































































































Результаты поиска

Содержание 600 SR

Отзывы:

Похожие инструкции для 600 SR

Бренды по названию

Популярные бренды

Braillo 600 SR, Руководство пользователя

Результаты поиска

Содержание 600 SR

Отзывы:

Похожие инструкции для 600 SR

Бренды по названию

Популярные бренды