Braillo 600 SR Скачать руководство пользователя страница 63

Страница: 63 / 119

4.8 Magnet rack, refitting and adjusting

Please see figure below:

Before putting the magnet rack back on the printer, make sure that the magnet rack itself is adjusted as

described in the previous chapter.

When replacing the magnet rack in the printer:

Put in the four fastening screws, but do not tighten them. Slide the magnet rack horizontally away from

the printer, so that the magnet rack is touching the horizontal adjustment screws. This will ensure that

the magnet rack is in exactly the same position as before it was taken off the printer.

See next chapter regarding correct adjustment of the magnet racks.

Note! All explanations refer to one magnet rack, but these adjustments must be done on all four

magnet racks.

BRAILLO

B 600 SR

Pull back against these

positioning screws

Содержание 600 SR
























































































































Результаты поиска

Содержание 600 SR

Отзывы:

Похожие инструкции для 600 SR

Бренды по названию

Популярные бренды

Braillo 600 SR, Руководство пользователя

Результаты поиска

Содержание 600 SR

Отзывы:

Похожие инструкции для 600 SR

Бренды по названию

Популярные бренды