Braillo 400 S 3 Series Скачать руководство пользователя страница 19

Страница: 19 / 97

I/O - Input/Output

Selects between serial and parallel port, and sets the data transmission values for the serial port.

1st push down: Displays which port is active.

To select serial or parallel port, the button must be depressed and then released. Now, while the display

still shows the active port, press SCROLL to select the other port.

If the serial port is active, a 2nd push down will make it possible to use SCROLL to adjust the settings

for the serial port.

ASCII-TABLES

This button has two functions:

It selects which 6 and 8 dot ASCII-table to be active for braille conversion and it displays the 6 and

8 dot ASCII-tables currently active.

1st push down:

Displays the active ASCII-table, number and country for the 6 dot mode.

2nd push down:

Displays the active ASCII-table, number and country for the 8 dot mode.

Note! This button will not change between the 6 and 8 dot print mode, it just displays which

ASCII-tables that will be used in these modes.

To select from the 8 resident ASCII-tables in the printer, the following procedure should be used:

Push the ASCII-tables button, release it, then push it once again and hold. Now it is possible to change

the active ASCII-tables with the SCROLL button. ASCII-table pair number one will be displayed ﬁ rst.

(If there has been a pair of ASCII-tables loaded from the computer, these will be displayed ﬁ rst). If

SCROLL is released, and pressed again, ASCII-table pair no. 2 will be displayed. This continues until

pair no. 8 is reached, whereafter it will start at pair number one again.

Note! Scrolling trough the resident ASCII-tables will clear any user table that has been

downloaded from the computer. If this table is to be activated again, it must be downloaded

from the computer again.

Using the “LAYOUT” menu buttons.

With help of the menu buttons (LAYOUT 1, LAYOUT 2, LAYOUT 3 and LAYOUT 4) the current

values can be changed.

The ﬁ rst push of a menu button shows which setting is currently active - its current value.

If these settings are correct, wait a few seconds for the timeout to expire, or press the RESET

PRINTER button and the setting will remain.

If you would like to change one of the settings, push the button several times, until the desired function

is shown on the display, then hold it down. By using SCROLL, the complete menu for the function

can be reviewed in the display. When the correct value is shown, release the button and either wait for

the timeout, or use RESET PRINTER.

Note! The Current Values are saved in the battery-backup memory, and they will remain even

if the power is turned off.

BRAILLO

●

NORWAY AS

B 400 Series 3

Содержание 400 S 3 Series


































































































Результаты поиска

Содержание 400 S 3 Series

Отзывы:

Похожие инструкции для 400 S 3 Series

Бренды по названию

Популярные бренды

Braillo 400 S 3 Series, Руководство пользователя

Результаты поиска

Содержание 400 S 3 Series

Отзывы:

Похожие инструкции для 400 S 3 Series

Бренды по названию

Популярные бренды