Brady BMP71 Скачать руководство пользователя страница 15

Страница: 15 / 147

Introduction

Firmware Upgrades

BMP71 User’s Manual

*Exposing the BMP71 printer to direct sunlight is not recommended.

WARNING

Avoid using the system near water, in direct sunlight, or near a heating device.

Do not attempt to use batteries other than those recommended in this manual.

Firmware Upgrades

Future upgrades to BMP71 firmware can be downloaded from Brady’s website. Access

www.bradyid.com/bmp71

, click Support>Downloads, then select BMP71 from the list of

products.

Environmental

Operation

Storage

Temperature* (Printer)

5° to 49° C (40° to 120° F)
Be mindful, when using the
AC adapter with the printer,
that the AC adapter is rated
at a maximum temperature
of 30° C (86° F).

-30° to 60° C (-24° to 140° F)

Relative Humidity
(Printer)

10% to 90 % (non-
condensing)

10% to 90% (non-
condensing

Temperature (AC
Adapter)

0 to 30° C (30° - 86° F)

-20° 85° C (-68° - 185° F)

Relative Humidity (AC
Adapter)

10% to 90% (non-
condensing)

5% - 90% (non condensing)

Содержание BMP71




















































































































































Результаты поиска

Содержание BMP71

Отзывы:

Похожие инструкции для BMP71

Бренды по названию

Популярные бренды

Brady BMP71, Руководство пользователя

Результаты поиска

Содержание BMP71

Отзывы:

Похожие инструкции для BMP71

Бренды по названию

Популярные бренды