background image

 

GENERAL INFORMATION 

 

This gas-fired water heater is design certified by CSA International under the 
applicable American National Standard, Z21.10.1 or Z21.10.3-(as indicated on 
the rating plate), or CSA 4.1-(as indicated on the rating plate), available from 
CSA International, 8501 East Pleasant Valley Road, Cleveland, OH U.S.A. 
44131-5575.  

 

This water heater must be installed in accordance with local codes. In the 
absence of local codes, it must be installed in compliance with the National 
Fuel Gas Code (ANSI Z223.1-Latest Edition), or in Canada CAN/CGA B149.1 
Natural Gas Installation Code (Latest Edition) or CAN/CGA B149.2 Propane 
Installation Code (Latest Edition). The warranty for this water heater is in 
effect only when the water heater is installed, adjusted, and operated in 
accordance with these Installation and Operating Instructions. The 
manufacturer will not be liable for any damage resulting from alteration and/or 
failure to comply with these instructions. 

 

This water heater is not design certified for installation in a mobile home. Such 
an installation may create a hazardous condition and will nullify the warranty. 

 

This water heater has been designed and certified for the purpose of heating 
potable water. The installation and use of this water heater for any purpose 
other than the heating of potable water may cause damage to the water 
heater, create a hazardous condition, and nullify the warranty. 

 
Do not use this appliance if any external part to the tank has been submerged 
in water. You should contact a qualified service technician to inspect the 
appliance and to replace any part of the control system including the 

combination gas control which has been submerged in water. See the Gas 
Connections section of this manual before servicing or replacing a water 
heater that has had any external part to the tank submerged in water. 

 

CAUTION

 

Incorrect operation of this appliance may create a hazard to life and 
property and will nullify the warranty.

 

 

WARNING 

Prior to connecting the gas supply line to a gas fired water heater, 
ensure that the gas supply line does not have moisture/water or 
dirt/scale inside the gas line. Commonly this check is done at the 
lowest point in the gas distribution system prior to gas burning 
appliances. 

 

DANGER

 

Do not store or use gasoline or other flammable, combustible, or 
corrosive vapors and liquids in the vicinity of this or any other 
appliance. 

Содержание RG275H10N

































Отзывы: