background image

 

13

Electrical Connections 

 

Before any electrical connections are made, be sure that the water heater is 
full of water and that the manual shut-off valve in the cold water supply line is 
open. Check the rating plate and wiring diagram before proceeding.  This 
electric water heater was built and wired in accordance with the Underwriters 
Laboratories testing approvals requirements.  The temperature limiting 
device is of the manual reset, trip-free type and has been factory installed to 
interrupt all ungrounded power supply conductors in the event of thermostat 
failure.  Thermostats are factory set and wired in accordance with the wiring 
diagram fastened to the inside of the top access panel.  The plumbing 
supplier in your area ordered this heater wired at the factory to comply with 
existing area codes, but local utility codes may require or allow other 
circuitry.  Consult your local power company to determine the correct 
electrical hook-up in order to meet local utility and building codes and in 
order to obtain the most economical rates.  Also check to find out if you are 
required to obtain a permit before starting the installation.  The following 
chart shows the recommended fuse size for the maximum water heater 
wattage.  The maximum wattage and rated voltage are shown on the water 
heater data plate.  The water heater must be well grounded.  A green ground 
screw is provided at the electrical connection point for connecting a ground 
wire.  Ground screw on 10 & 15-gallon models is located under the 
removable element cover. 

 

Recommended Fuse size 

 Voltage 

Max. 

Watts  120v  208v 240v 277v 480v 

1000 

15A  10A 10A 10A 10A 

1250 

15A  10A 10A 10A 10A 

1500 

20A  10A 10A 10A 10A 

2000 

25A  15A 15A 10A 10A 

2500 

30A  15A 15A 15A 10A 

3000 

35A  20A 20A 15A 10A 

3500 

---  25A 20A 20A 10A 

4000 

---  25A 25A 20A 15A 

4500 

---  30A 25A 25A 15A 

5000 

---  30A 30A 25A 15A 

5500 

---  35A 35A 25A 15A 

6000 

---  40A 35A 30A 20A 

 

 
 
 
 
 

Содержание 238-44422-00G





















Отзывы: