Bouffalo Lab BL602 Скачать руководство пользователя страница 149

Страница: 149 / 195

BL602/604 Reference Manual

11.7.2 DMA receiving process

1. Configure the read and write flags to 1

2. Configure the slave device address

3. Configure Slave Device Address

4. Configure slave device address length

5. Data length

6. Set the enable signal register

7. Configure DMA transfer size

8. Configure the DMA source address transfer width (Note that when I2C is used with DMA, the source address

transfer width needs to be set to 32bits and used in word alignment)

9. Configure DMA destination address transfer width

10. Configure the DMA source address as I2C RX FIFO address, I2C_FIFO_RDATA

11. Configure the DMA destination address as the memory address to store the received data

12. Enable DMA

11.8 Interrupt

I2C includes the following interrupts:

• I2C_TRANS_END_INT: I2C transfer end interrupt

• I2C_TX_FIFO_READY_INT: Interrupt is triggered when I2C TX FIFO has free space available for filling

• I2C_RX_FIFO_READY_INT: When I2C RX FIFO receives data, trigger interrupt

• I2C_NACK_RECV_INT: When the I2C module detects a NACK state, an interrupt is triggered

• I2C_ARB_LOST_INT: I2C arbitration lost interrupt

• I2C_FIFO_ERR_INT: I2C FIFO ERROR interrupt

11.9 Register description

Name

Description

i2c_config

I2C configuration register

i2c_int_sts

I2C interrupt status

i2c_sub_addr

I2C sub-address configuration

BL602/604 Reference Manual

149/ 195

@2020 Bouffalo Lab

Содержание BL602



































































































































































































Результаты поиска

Содержание BL602

Отзывы:

Похожие инструкции для BL602

Бренды по названию

Популярные бренды

Bouffalo Lab BL602, Справочное руководство

Результаты поиска

Содержание BL602

Отзывы:

Похожие инструкции для BL602

Бренды по названию

Популярные бренды