manualshive.com logo in svg

BossWeld Buddy MIG 150, Инструкция по эксплуатации

Поделиться
Скачать
BossWeld Buddy MIG 150 Скачать руководство пользователя страница 14

14

DISPOSING OF THE PACKAGING 

Recycling packaging reduces the need for landfill and raw materials. Reuse of the recycled material 

decreases pollution in the environment. Please recycle packaging where facilities exist. Check with 

your local council authority for recycling advice.

 

DISPOSING OF THE WELDER 

Welders that are no longer usable should not be disposed of with household waste but in an 

environmentally friendly way. Please recycle where facilities exist. Check with your local council 

authority for recycling advice.

Problem

Suggested Remedy

No wire feed

1.  Check that the MMA/MIG selector switch set to MIG position

Inconsistent / interrupted 

wire feed

1.  Be sure to adjust the wire feed and voltage dials for MIG welding.  

The current dial is for MMA welding mode.

2.  Select the correct polarity for the wire being used.

3. Incorrect wire speed: adjust the wire feed speed

4. Incorrect voltage: adjust the voltage setting

5. MIG Torch kinked: remove the kink, reduce the angle or bend

6. Tip worn/incorrect: replace the tip with correct size and type

7.  Liner worn/clogged/incorrect size: try to clear the liner by blowing 

out with compressed air as a temporary cure, it is recommended to 

replace the liner regularly. Install the correct size liner.

8. Blocked/worn inlet guide: clear or replace the inlet guide tube

9.  Misaligned in drive roller groove: reposition the wire into the groove 

of the drive roller

10.  Incorrect/worn drive roller: fit the correct size/type drive roller. 

Replace drive roller

11.  Drive roller pressure too high: reduce the drive roller pressure.

12. Tension high on wire spool hub: reduce the spool hub brake tension

13:  Wire tangled/crossed: remove the spool untangle the wire or  

replace the wire.

14.  Contaminated MIG wire: use clean dry rust free wire. Do not 

lubricate the wire with oil, grease etc.

TROUBLE SHOOTING - WIRE FEEDER

DISPOSAL

Содержание Buddy MIG 150

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды