Boss GT-001, Руководство по параметрам

Страница: 10 / 48

EFFECT
10
SUB OD/DS
This effect distorts the sound to create long sustain.
Knob Parameter Value Explanation
Page 1
[1] TYPE
Refer to “OD/DS TYPE” (p. 3).
* “CUSTOM” is not available.
* “A-DIST” can be used only with FX2.
[2] DRIVE 0–120 Adjusts the depth of distortion.
[3] TONE
-50–+50 Adjusts the tone.
[4]
E .LEVEL
(EFFECT LEVEL)
0–100
Adjusts the volume of the effect
sound.
Page 2
[1] BOTTOM
-50–+50
Adjusts the tone for the low
frequency range. Turning this to the
left (counterclockwise) produces a
sound with the low end cut; turning
it to the right boosts the low end in
the sound.
[2]
DIR .MIX
(DIRECT MIX)
0–100
Adjusts the volume of the direct
sound.
[3]
SOL .SW
(SOLO SW)
OFF, ON The tone to one suitable for solos.
[4]
SOL .LV
(SOLO LEVEL)
0–100
Adjusts the volume level when the
Solo Sw is ON.
GRAPHIC EQ
This adjusts the tone. You can adjust the sound quality in ten bands.
Knob Parameter Value
Page 1
[1]
31 Hz
-20–+20 dB
[2] 62 Hz
[3] 125 Hz
[4] 250 Hz
Page 2
[1]
500 Hz
[2] 1 kHz
[3] 2 kHz
[4] 4 kHz
Page 3
[1]
8 kHz
[2] 16 kHz
[4] LEVEL -20–+20 dB
PARAMETRIC EQ
This adjusts the tone. You can adjust the sound quality in four
bands.
Knob Parameter Value Explanation
Page 1
[1]
LO .GAIN
(LOW GAIN)
-20–+20 dB
Adjusts the low frequency
range tone.
[2]
HI .GAIN
(HIGH GAIN)
-20–+20 dB
Adjusts the high frequency
range tone.
[4] LEVEL -20–+20 dB
Adjusts the overall volume
level of the equalizer.
Page 2
Knob Parameter Value Explanation
[1]
LM .FREQ
(LOW-MID FRE-
QUENCY)
20 Hz–10.0 kHz
Specifies the center of
the frequency range that
will be adjusted by the
LOW-MID GAIN.
[2] LM .Q (LOW-MID Q) 0.5–16
Adjusts the width of the
area affected by the EQ
centered at the LOW-MID
FREQ. Higher values will
narrow the area.
[3]
LM .GAIN
(LOW-MID GAIN)
-20–+20 dB
Adjusts the low-middle
frequency range tone.
Page 3
[1]
HM .FREQ
(HIGH-MID FRE-
QUENCY)
20 Hz–10.0 kHz
Specifies the center of
the frequency range that
will be adjusted by the
HIGH-MID GAIN.
[2]
HM .Q
(HIGH-MID Q)
0.5–16
Adjusts the width of the
area affected by the EQ
centered at the HIGH-MID
FREQ. Higher values will
narrow the area.
[3]
HM .GAIN
(HIGH-MID GAIN)
-20–+20 dB
Adjusts the high-middle
frequency range tone.
Page 4
[1]
LO .CUT
(LOW CUT)
FLAT, 20 Hz–800 Hz
This sets the frequency
at which the low cut filter
begins to take effect. When
“Flat” is selected, the low
cut filter will have no
effect.
[4]
HI .CUT
(HIGH CUT)
630 Hz–
12.5 kHz, FLAT
This sets the frequency at
which the high cut filter
begins to take effect. When
“FLAT” is selected, the
high cut filter will have no
effect.
TONE MODIFY
This changes the tone of the connected guitar.
Knob Parameter Value Explanation
Page 1
[1] TYPE
Selects the type of tone modification.
FAT
Fat tone with boosted mid
range.
PRES (PRESENCE)
Bright tone with boosted
high-mid range.
MILD
Mild tone with the high end
cut back.
TIGHT
Tone with the low frequencies
cut.
ENHANC (ENHANCE)
Tone with the high frequencies
boosted.
RESO1 – 3
(RESONATOR1–3)
This produces a tone with
greater power and punch
by adding resonance in the
low-frequency range and
midrange.
[2] LOW -50–+50
Adjusts the tone for the low
frequency range.
[3] HIGH -50–+50
Adjusts the tone for the high
frequency range.
[4] LEVEL 0–100
Adjusts the volume of the
effect sound.
Page 2
[1] RESO
0–100
This adjusts the strength of
the low-end and midrange
resonance when TYPE is set to
RESO 1, 2, or 3.