background image

BOSS Products limited consumer warranty and BOSS
Products commercial warranty policies are located at

www.bossplow.com

.

Patent

www.ttcopats.com

.

Introduction

This spreader is designed to dispense ice-control
solutions on residential or commercial properties.
Using this product for purposes other than its intended
use could prove dangerous to you and bystanders.

Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. You are responsible for
operating the product properly and safely.

Visit

www.bossplow.com

for product safety and

operation training materials, accessory information,
help finding a dealer, or to register your product.

Whenever you need service, genuine BOSS parts, or
additional information, contact an Authorized BOSS
Dealer or BOSS Technical Service (1-800-286-4155)
and have the model and serial numbers of your
product ready.

Figure 1

identifies the location of the

model and serial numbers on the product. Write the
numbers in the space provided.

g382865

Figure 1

1.

Serial number location

Model No.

Serial No.

The safety-alert symbol shown in this manual and on
the machine identifies important safety messages that
you must follow to prevent accidents.

g000502

Figure 2

Safety-alert symbol

The safety-alert symbol appears above information
that alerts you to unsafe actions or situations and
is followed by the word

DANGER

,

WARNING

, or

CAUTION

.

DANGER

indicates an imminently hazardous situation

which, if not avoided, will result in death or serious
injury.

WARNING

indicates a potentially hazardous situation

which, if not avoided, could result in death or serious
injury.

CAUTION

indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate
injury.

This manual uses 2 words to highlight information.

Important

calls attention to special mechanical

information and

Note

emphasizes general information

worthy of special attention.

Contents

Safety ....................................................................... 3

Preparation......................................................... 3
Operation............................................................ 3
Safety and Instructional Decals .......................... 4

Setup ........................................................................ 5

Installing the Mounting Plates ............................. 5
Installing the Spreader on the Mounting

Plates.............................................................. 6

Installing the Controller ....................................... 7
Routing the Wire Harness................................... 8

Product Overview ..................................................... 9

Controls ............................................................. 9
Specifications .................................................... 9

Operation ................................................................ 10

Removing the Spreader.................................... 10
Loading the Spreader ....................................... 10
Operating the Spreader .................................... 10
Freeing a Clog ...................................................11
Adjusting the Material Deflectors .......................11
Unloading the Spreader.....................................11
Cleaning the Spreader.......................................11

Troubleshooting ...................................................... 12

© 2022—BOSS Products
P.O. Box 787
Iron Mountain, MI 49801

2

Contact us at www.bossplow.com.

Printed in the USA

All Rights Reserved

 

 

Содержание SNR24030













Отзывы: