background image

 

Safety Instructions 

The safety recommendations outlined in this section are to be read, 
understood and followed before operating the product. Keep this 
information in a safe place for future reference. Failure to comply with any 
of the following safety procedures could result in serious hazard. 

 

Do not operate product for any purposes other than its intended use 

 

This product is intended for indoor use only 

 

Do not operate product if power cord is damaged in anyway 

 

Do not insert objects into openings 

 

Do not immerse product in water or permit liquids to spill inside 

 

Turn off power when unattended or not in use. Unplug product before 

moving it or when it is not in use for an extended period of time. The 

socket-outlet shall be installed near the equipment and shall be easily 

accessible 

 

Do not alter or extend electric plug. Plug is configured for appropriate 

electrical supply 

 

Do not overload electrical outlets beyond their capacity as this can result in a 

fire 

NOTE: 

DO NOT TOUCH THE PRODUCT OR ANY OTHER SENSITIVE 

COMPONENTS WITHOUT ALL NECESSARY ANTI-STATIC 

PROTECTIONS. 

Содержание BPC-6671























Отзывы: