Bose Panaray MSA12X Скачать руководство пользователя страница 45

Страница: 45 / 52

Design Guide - 45

Appendix: How to Set Up IP Address

We recommend having a router or DHCP server in the system for setting up, which will make the setup

process simple and easy. However there will be cases where you do not have a router/DHCP server. This

appendix shows example IP setting processes for typical situations.
For more complex Network settings, please contact the IT representative personnel.

Note:

Dante® Controller must be installed on your PC (download:

https://www.audinate.com/

)

With EX-1280C or 1U ESP with Dante® Card, No Router

1.  Connect PC and all the devices to the network.
2.  Set IP of PC to DHCP.
3.  Launch Dante Controller.

a. Make sure all the Dante Devices (incl. MSA12X arrays, ESP) appear.
b. At this point, all the Dante Devices should be

i. IP: 169.254.xxx.xxx
ii. Subnet Mask: 255.255.0.0

4. Change IP of all the Dante devices to static:

i. IP: 192.168.0.xxx (e.g. 101, 102, …)
ii. Subnet Mask: 255.255.255.0

Each time you change the IP, that Dante device may disappear in the Dante Controller, or even if it can be

seen, you may not be able to assign Dante subscriptions. This is OK.

Switch

MSA12X

Dante Card

ESP

DHCP

IP: 169.254.xxx.xxx

Subnet: 255.255.0.0

DHCP

IP: 169.254.xxx.xxx

Subnet: 255.255.0.0

DHCP

IP: 169.254.xxx.xxx

Subnet: 255.255.0.0

DHCP

IP: 192.168.0.160

Subnet: 255.255.255.0

Dante Device IP automatically

given by Dante link local

DHCP

IP: 169.254.xxx.xxx

Subnet: 255.255.0.0

Switch

MSA12X

Dante Card

ESP

DHCP

IP: 169.254.xxx.xxx

Subnet: 255.255.0.0

Static

IP: 192.168.0.

102

Subnet: 255.255.255.0

Static

IP: 192.168.0.

101

Subnet: 255.255.255.0

DHCP

IP: 192.168.0.160

Subnet: 255.255.255.0

IP: 192.168.0.

103

Subnet: 255.255.255.0

Static

Last 3 digits of IP (bold)

are just examples

Содержание Panaray MSA12X





















































Результаты поиска

Содержание Panaray MSA12X

Отзывы:

Бренды по названию

Популярные бренды

Bose Panaray MSA12X, Руководство по конструкции

Результаты поиска

Содержание Panaray MSA12X

Отзывы:

Бренды по названию

Популярные бренды