Bose Panaray MSA12X Скачать руководство пользователя страница 42

Страница: 42 / 52

42 - Design Guide

Frequently Asked Questions

What is the angular limit for Basic Steering/Spreading?

Array

1-module

2-module

3-module

Steer

–20° to +20°

Spread

0° to 30°

What is the frequency limit for the beam control?

It depends on the length of the array. The longer the array, the lower the frequency limit for the beam control.

A rough guide is shown below:

1-module array: 500 Hz
2-module array: 250 Hz
3-module array: 160 Hz

How many modules per array are supported?

Up to 3 modules stack per array is supported.

How many modules do I need for the dual beam?

Regardless of number of modules of an array, up to two beams (single beam or dual beam) can be radiated. It

is recommended to use a 2- or 3-module MSA12X array for better directivity control due to the longer array.

How many beams can be radiated from one array?

Currently, up to two beams per array (dual beam) are supported.

Do I need a power amplifier for driving a MSA12X array?

No. MSA12X is a powered loudspeaker with amplifiers in it, and you do not need additional power amplifiers.

Does MSA12X have DSP inside? Do I need an external signal processor?

MSA12X has on-board DSP inside, which manages Speaker EQ, beam shaping, beam gain and Beam EQ. If you

need to apply more signal processing such as Room EQ or signal delay for rear arrays, you need an additional

signal processor such as Bose ESP in the upstream of the system.

1-module array

Steer: ± 20°

Spread: Up to 30° (± 15°)

−20°

15°

2- or 3-module array

Steer: ± 20°

Spread: Up to 40° (± 20°)

−20°

20°

30°

40°

Ear

Height

0.3-0.8 m

(1’-2.5’)

Max Recommended

Содержание Panaray MSA12X





















































Результаты поиска

Содержание Panaray MSA12X

Отзывы:

Бренды по названию

Популярные бренды

Bose Panaray MSA12X, Руководство по конструкции

Результаты поиска

Содержание Panaray MSA12X

Отзывы:

Бренды по названию

Популярные бренды